Table of Contents
Advertisement
Quick Links
NOTE: Depending on your Winston Workstation
you may not receive all the parts shown within this instruction booklet.
Installation may require two people.
800.524.2744 InnovativeWorkspaces.com
.....................................................Page 9
configuration,
®
Winston Workstation
5
3
2
PAGE 1 OF 10
WNST-1 & WNST-2
Single & Dual | Installation Instructions
®
4
© 2018 Innovative Office Products, LLC
1
7
6
P512242 REV D
Advertisement
Table of Contents
Related Manuals for Innovative WNST-1
Summary of Contents for Innovative WNST-1
-
Page 1: Table Of Contents
NOTE: Depending on your Winston Workstation configuration, ® you may not receive all the parts shown within this instruction booklet. Installation may require two people. 800.524.2744 InnovativeWorkspaces.com PAGE 1 OF 10 © 2018 Innovative Office Products, LLC P512242 REV D... -
Page 2: Wnst-1 & Wnst
407747 Felt Pad Top Plate 7/32" Allen Wrench M4 x 12mm PhPHS 111464 111736 701127 702096 Freestanding Base (WNST-1 only) Utility Tray Column Cap Fine Tune Adjust (optional) 111731 113025 111275-708 8473 Freestanding Base (WNST-2 only) 10-32 x 1" FHSCS 10-32 x 3/8"... -
Page 3: Step 1 | Column
STEP 1 COLUMN IMPORTANT: Do not pull excessively on cable – doing so may result in accidental actuation of column. CAUTION: Do not press height adjust button until unit is fully assembled. Confirm cable is properly seated into position. Use 7/32" Allen wrench to press cable firmly into place. -
Page 4: Step 2 | Mount
STEP 2 FREESTANDING MOUNT Hang base plate over edge of Place work surface work surface to allow access on base plate to aid as a to countersunk holes. Side counterbalance. of base plate with felt pads should be face down. D or E 7/32"... -
Page 5: Step 3 Work Surface
STEP 3 WORK SURFACE Slide utility tray onto work surface. Utility tray simply rests on top of work surface. 800.524.2744 InnovativeWorkspaces.com PAGE 5 OF 10... -
Page 6: Step 4 | Beam
STEP 4 BEAM 1/8" IMPORTANT: Tighten bolts evenly. The beam should sit flush against the column, ensure there are no gaps. Also, it is important the work surface clamp is level. 1/8" 800.524.2744 InnovativeWorkspaces.com PAGE 6 OF 10... -
Page 7: Step 5 Monitor Tilter
STEP 5 MONITOR TILTER STANDARD TILTER & SPRING TILTER S or T FINE TUNE HEIGHT ADJUST TILTER S or T 800.524.2744 InnovativeWorkspaces.com PAGE 7 OF 10... -
Page 8: Step 6 Monitor Cups
STEP 6 MONITOR CUPS 7/32" 1/8" 800.524.2744 InnovativeWorkspaces.com PAGE 8 OF 10... -
Page 9: Step 7 Cable Management
STEP 7 CABLE MANAGEMENT 800.524.2744 InnovativeWorkspaces.com PAGE 9 OF 10... - Page 10 HEIGHT ADJUSTMENT Press button and hold. Lift up/down. Release to lock in place. Is your height adjust button not working? If so, make the adjustments below. Slide workstation so that the work surface hangs over desk edge to allow access to underneath the work surface.
Need help?
Do you have a question about the WNST-1 and is the answer not in the manual?
Questions and answers