Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for hengel Bi-Tronic Control
Summary of Contents for hengel Bi-Tronic Control
- Page 1 User instructions Bi-Tronic Control Deep freezing / Fast chilling To be conserved by the user Hengel Industrie ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE Email : infos@hengel.com Notice-EN-BITRONIC-ST-SRR-1 Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09...
- Page 2 Initial document creation YM / SG Hengel Industrie ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE Email : infos@hengel.com Notice-EN-BITRONIC-ST-SRR-1 Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09 Website: www.hengel.com...
-
Page 3: Table Of Contents
5 - STOPPING THE CONTROL INTERFACE ........9 Hengel Industrie ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE Email : infos@hengel.com Notice-EN-BITRONIC-ST-SRR-1 Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09... -
Page 4: General Introduction
1 - GENERAL INTRODUCTION The company HENGEL thanks you for your trust. The new HMI Bi-tronic is simple, intuitive, and composed by seven-segment display. It is in the following form: Interface areas Operating state Display Current mode indication area Switching to time... -
Page 5: Key's List And Leds
• Blinking red: fault or error Hengel Industrie ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE Email : infos@hengel.com Notice-EN-BITRONIC-ST-SRR-1 Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09 Website: www.hengel.com... -
Page 6: Example Of Use
This mode is not activated in the case of blast chilling. Hengel Industrie ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE Email : infos@hengel.com Notice-EN-BITRONIC-ST-SRR-1 Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09... -
Page 7: Direct Mode
Confirm by pressing the “Enter” key. Hengel Industrie ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE Email : infos@hengel.com Notice-EN-BITRONIC-ST-SRR-1 Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09 Website: www.hengel.com... -
Page 8: Display During The Cycle
For this, make a long press on the “Enter” button. Hengel Industrie ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE Email : infos@hengel.com Notice-EN-BITRONIC-ST-SRR-1 Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09... -
Page 9: Faults And Parameters
Action to take if verification Fault Check Observation fault does not solve the problem Change the EEPROM of the Order part from Hengel regulation Change the regulation Order part from Hengel If the temperature probe is Change the temperature The machine does not work...
Need help?
Do you have a question about the Bi-Tronic Control and is the answer not in the manual?
Questions and answers