Subscribe to Our Youtube Channel
Related Manuals for Axminster Craft AC200WDG
Summary of Contents for Axminster Craft AC200WDG
- Page 1 Code 105246 Original Instructions AC200WDG 150/200mm Wet & Dry Grinder AT&M: 09/04/2019 BOOK REF : 105790...
-
Page 2: Eu Declaration Of Conformity
EN 61000-3-3:2008 EN 55014-2:1997+A1+A2 Type Wet & Dry Grinder Model AC200WDG and conforms to the machinery example for which the EC Type-Examination Certificate No AM 50269230, AN 50269231, AE 50269284 has been issued by Wendeng Allwin Motors Manufacturing Co., Ltd. Signed at: No. -
Page 3: What's Included
What’s Included Quantity Item Part Model Number AC200WDG Wet & Dry Grinder Eye shield mounting bar Spark guard bracket Mounting bar square bracket Threaded bolt Small screw with spring & flat washers Flat washer Tool rest with drill bit recess Star locking knob with flat &... -
Page 4: General Instructions For 230V Machines
General Instructions for 230V Machines • Leave machine unplugged until work is about to The following will enable you to observe good working practices, keep yourself and fellow workers safe and commence. maintain your tools and equipment in good working order. •... - Page 5 Specific Safety Precautions for Grinding Machines 11. Hot sparks are a hazard! Never carry out grinding 16. Avoid awkward hand positions where a sudden slip operations near flammable gas or liquid. could cause the hands to come into contact with a grinding wheel, wire brush etc.
- Page 6 Assembly/Setup Lower the shield • Adjust the spark guard bracket (C) until it’s just clear of the stone. Loosen the nut • Adjust the tool rest (H) the same as described above. Drain plug Make sure the draining plug is inserted into the base of •...
-
Page 7: Specification
Clean the trough and refill with clean water frequently. See page 12 for removing the trough. Specification Code 105246 Model AC200WDG Rating Craft Power 250W 230V 50Hz 1Ph Wheel Speed (Dry/Wet) 2,850rpm/130rpm... -
Page 8: Illustration And Parts Description
Illustration and Parts Description Slow running grinding stone Eye shield guard Motor Tool rest Water trough Gearbox Tool rest clamping knob Bench mounting hole On/Off switch Storage drawer Eye shield mounting Water trough drain plug Stone guard... - Page 9 Illustration and Parts Description On/Off Switch Trough draining plug Storage drawer Tool rest with drill bit angle recess Grinding stone eye shield guard Support notches to steady tools being offered up to the stone...
-
Page 10: Operating Instructions
Operating Instructions hand if you need it. Fill the trough with 15-20mm water, see CONNECT THE GRINDER TO THE page 07. Start the machine, wait until it reaches full speed. MAINS SUPPLY. Check it runs smoothly, no knocking or scraping noises for example. - Page 11 Changing the 150mm Grinding Stone Rotate the guard cover Tighten the three screws Remove plate flange and carefully remove the stone. Clean the interior stone guard, inspect the new stone for CONNECT THE GRINDER cracks and damage to either the front face or the edges TO THE MAINS SUPPLY.
- Page 12 Changing the 200mm Wetstone DISCONNECT THE GRINDER FROM THE MAINS SUPPLY. Place a container under the trough and drain the water by removing the drain plug from beneath. Trough Loosen and lower the nut/bolt beneath the gearbox assembly and remove the trough. Drain plug Loosen the upper clamping screws...
- Page 13 Changing the 200mm Wetstone Remove plate flange and carefully remove the stone. Grasp the stone using a cloth, use a 19mm spanner to Clean the drive shaft and rear plate flange, inspect the new loosen the nut, remember undo the nut in the direction stone for cracks and damage to either the front face or the of the stone’s rotation.
- Page 14 Dressing the Stone Code 410057 CONNECT THE GRINDER TO THE MAINS SUPPLY. If the grinder starts to vibrate or uneven wear appears on the stones including, crests dips or rounded edges you may need to dress the stones. The stones will need to be dressed out using a suitable wheel dressing stick.
- Page 15 Exploded Diagrams/Lists...
- Page 16 Exploded Diagrams/Lists Description Specification Qty Strain relief Storage drawer Plug and cord Base assembly Bolt M6 x 18 Phillips screw+flat M4 x 6 Water block washer assembly Hex nut Phillips M4 x 8 Hex bolt M5 x 16 Screw+spring Wet wheel stone washer+flat washer guard assembly...
- Page 17 Exploded Diagrams/Lists Flat washer Wheel flange Q235 Phillips screw M5 x 16 Wheel stone 150 x 20 x 12.7mm Case body ADC12 Right wheel guard Q235 Retainer ring Spark deflector Q235 Wet wheel flange Lock washer Wet wheel stone 200 x 40 x Right tool rest Q235 20mm...
-
Page 18: Wiring Diagram
Wiring Diagram... - Page 19 Notes...
- Page 20 The Axminster guarantee is available on Craft, Trade, Engineer, Air Tools & CNC Technology Series machines Buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! For more information visit axminster.co.uk/3years The packaging is suitable for recycling.
Need help?
Do you have a question about the AC200WDG and is the answer not in the manual?
Questions and answers