Subscribe to Our Youtube Channel
Related Manuals for Axminster Craft AC200BG
Summary of Contents for Axminster Craft AC200BG
- Page 1 AC150BG Code 105242 AC200BG Code 105243 Original Instructions AC150BG, AC200BG Bench Grinders AC150BG AC200BG AT&M: 02/04/2019 BOOK REF : 105787...
-
Page 2: Eu Declaration Of Conformity
2006/42EC EN61029-1:2009+A11:2010 declares that the machinery described:- EN61029-2-4:2011 Bench Grinder Type AC150BG, AC200BG Model and conforms to the machinery example for which the EC Type-Examination Certificate No EFSH13081056-IE-01-V02 has been issued by Wendeng Allwin Motors Manufacturing Co., Ltd Signed at: No.15 Sichan Road, Wendeng, 264400, Shandong, China and complies with the relevant essential health and safety requirements. -
Page 3: What's Included
Part Model Number AC150BG AC200BG 150mm Grinder 200mm Grinder Quantity Item Part Bolts & washers for AC150BG Tool rest brackets Butterfly knobs & washers for AC200BG Eye shields Eye shield arms with long bolts & washers Instruction manual Magnifying glass... -
Page 4: General Instructions For 230V Machines
General Instructions for 230V Machines • Leave machine unplugged until work is about to The following will enable you to observe good working practices, keep yourself and fellow workers safe and commence. maintain your tools and equipment in good working order. •... - Page 5 Assembly Step 1 Step 2 AC200BG Locate the tool rests (D) and secure them to the stone guard housings using the bolts/washers (C) for the AC150BG and the two butterfly knobs/washers (E) for the AC200BG. Continues Over...
- Page 6 Assembly Step 3 Step 4 Threaded hole Gears Remove the clamping knobs (A) from the eye shields (F). Locate Locate the two long bolts (G), place a spring/washer over the the eye shield arms (G) and mess the two gears together. bolts.
-
Page 7: Illustration And Parts Description
Housing slot for bolting the grinder Storage draw to the work bench Eye shield guard Eye shield adjusting knob AC200BG Tool rest Stone guard Tool rest will drill bit angle recess On/Off switch Tool rest butterfly clamping knob... -
Page 8: Specification
Specification Code 105242 Code 105243 Model AC150BG Model AC200BG Rating Craft Rating Craft Power 250W 230V 50Hz 1Ph Power 550W 230V 50Hz 1Ph Speed 2,850rpm Speed 2,850rpm Wheel Diameter 150mm Wheel Diameter 200mm Wheel Width 20mm Wheel Width 25mm Bore 12.7mm... - Page 9 Setting Up the Grinder Carry out final checks e.g. check the gap between the tool rest and the stone is correct, check the stone is not badly CONNECT THE GRINDER TO THE deformed (rounded edges, grooved face, etc; unless you MAINS SUPPLY.
- Page 10 Changing the Grinding Stone/Dressing the Stone Step 4 CONNECT THE GRINDER TO THE MAINS SUPPLY. Reconnect the grinder to the mains supply, give the grinder a ‘short burst’ , by switching it on and off quickly. Check the grinder is not subject to any undue vibration. If the grinder does vibrate, switch off immediately and disconnect from the main supply.
- Page 11 Dressing the Stone/Changing the Light Bulbs Changing the Light Bulb Code 410057 To replace a blown light bulb, follow the instruction below. Step 1 Phillips screw Diamond Dressing Block useful for dressing across the width of the grinding wheels or to produce flatter surfaces than single point dressers.
- Page 12 Exploded Diagrams/Lists AC150BG Bench Grinder...
- Page 13 Exploded Diagrams/Lists Description Spec Cord clip Wire with plug Phillips screw M4 x 8 Cord clip plate Hex nut Phillips screw + spring M4 x 8 Left wheel cover washer + flat washer Type I hex nut M12 left Hex nut Wheel flange Switch board Grinding wheel (WA...
- Page 14 Exploded Diagrams/Lists AC2000BG Bench Grinder...
- Page 15 Exploded Diagrams/Lists Descriptions Spec Spring washer Phillips screw M4 x 8 Hex nut Sleeve Switch plate Left wheel guard cover Switch Type 1 hex nut Flat washer Wheel flange Tooth lock wash Wheel stone Motor housing Phillips screw M5 x 10 Cord sleeve Spring washer Stator...
- Page 16 The Axminster guarantee is available on Craft, Trade, Engineer, Air Tools & CNC Technology Series machines Buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! For more information visit axminster.co.uk/3years The packaging is suitable for recycling.
Need help?
Do you have a question about the AC200BG and is the answer not in the manual?
Questions and answers