Download Print this page

TechNexion TEK5-APL Quick Start Manual

Embedded fanless box pc
Hide thumbs Also See for TEK5-APL:

Advertisement

Quick Links

INNOVATORS OF TECHNOLOGY
TEK5-APL
Quickstart Guide
1
Safety Precautions
Thank you for purchasing a TechNexion TEK series device. This installation guide will be helpful in the installation, wiring and inspection of your TechNexion embedded
fanless box PC. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precautions before proceeding with
the installation, wiring, and operation. Place this instruction sheet in a safe location for future reference. The following suggestions will help you.
1.1
Storage and Installation
• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet,
allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.
!
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.
• Do not attempt to open the device. This product is designed for specific applications and needs to be installed by qualified personnel.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not paint the device. Paint can clog the parts and prevent proper operation.
• Unauthorized modifications or attachments could damage the device and may violate regulations governing radio devices.
1.2
Wiring
•Make sure that the available power source matches the required input power of the device. Failure to observe this caution may result in electric shock or fire.
•Do not power the unit by DC input when you apply power over the PoE (RJ45).
1.3
Maintenance and Inspection
• Do not touch any internal or exposed parts of the device as electrical shock may result.
• Do not open the device while power is on. Otherwise electrical shock may result.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Be sure the ventilation holes are not obstructed during operation. Otherwise malfunction may result due to bad ventilation or overheating.
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service
facility for service.
2
Dimensions
286
270
250
Unit : mm
1
3
Installation Instructions
This section describes the mounting procedures for TEK series device. The material in the mounting area must provide sufficient strength for support of this embedded
box PC.
3.1
Surface Mounting
There are 4 mounting holes (M5) on the top side of the device required for surface mounting. Four M4 or M5 screws with at least 8mm head-to-tip length are required
to secure this device to the surface.
4
External Connectors
Front view:
1
2A
2B
3
4
5A
6
7 8 9
11A
12 5B
13
14
15
16
17
11B
No.
Description
1
Power Input connector
2A
SIM1 (Mini-SIM) card slot
2B
SIM2 (Mini-SIM) card slot
3
microSD card slot
4
2x USB 3.0 Host connector
5A
2x USB 2.0 Host connector
5B
2x USB 2.0 Host connector
6
LED Light 1/2/3/4 indicators
7
Power LED indicator
8
SATA LED indicator
9
Power button
10
Reset button
11A
Antenna hole
11B
Antenna hole
12
Grounding screw
13
LAN1 RJ45 connector
14
LAN2 RJ45 connector
Rear view:
10
18 19C
19A
20
21
22 23
24A
19D
19B
25
24B
24C
No.
Description
15
OPT-A connector hole
16
OPT-B connector hole
17
2.5" SSD Drive Rack
18
GPIO DB15 connector
19A
RS-XXX1 (Serial Port) DB9 connector
19B
RS-XXX2 (Serial Port) DB9 connector
19C
RS-XXX3 (Serial Port) DB9 connector
19D
RS-XXX4 (Serial Port) DB9 connector
20
DVI-D connector
21
DP connector
22
3.5mm jack Mic in
23
3.5mm jack Line out
24A
Antenna hole
24B
Antenna hole
24C
Antenna hole
25
VGA (15-pin D-SUB) connector
2

Advertisement

loading
Need help?

Need help?

Do you have a question about the TEK5-APL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for TechNexion TEK5-APL

  • Page 1 Safety Precautions Thank you for purchasing a TechNexion TEK series device. This installation guide will be helpful in the installation, wiring and inspection of your TechNexion embedded fanless box PC. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precautions before proceeding with the installation, wiring, and operation.
  • Page 2 • No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent permitted by law no liability (including liability to any person by reason of Ground negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document. SERIAL1/2/3/4_DSR...