Philips CE120/55 Quick Start Manual page 2

3
English
1 Black To a metal surface of the car
First connect the black ground
(earth) lead, then connect the
Overview of parts
yellow and red power supply
leads.
These are the supplied parts needed to connect
2 Blue To the electric antenna control
and install this unit.
lead or power supply lead of the
a Carry case with front panel stored inside
antenna booster
If there is no electric antenna or
b Trim plate
antenna booster, or it is manually
c Standard connector operated telescopic antenna, it
is not necessary to connect this
d Disassembly tool x 2 pcs
lead.
e Rubber cushion
3 To the +12V car battery which
Yellow
is energized at all times .
f Screw x 4 pcs
4 Pink To telephone mute terminal (if
g Mounting bolt
any) .
5 Red To the +12V power terminal
Connect wires: ISO connectors which is energized in the ac-
cessory (ACC) position of the
ignition switch
If there is no accessory position,
1
Pull out the ISO connectors from car
connect to the +12V car battery
dashboard and connect them to the bigger
terminal that is always live. Be
end of the supplied standard connector.
sure to connect the black ground
2
Connect the other end of the supplied
(earth) lead to a metal surface of
standard connector to the unit.
the car fi rst.
3
Do the other connections, if applicable.
6 Green/ Left speaker (Rear)
black
1 Antenna To antenna
strip
7 White/ Left speaker (Front)
2 Rear line out To amplifi er line in (right)
(right) black
strip
3 Rear line out To amplifi er line in (left)
(left) 8 Gray/ Right speaker (Front)
black
strip
Connect wires: without ISO
connectors
9 Purple/ Right speaker (Rear)
black
1
Cut off the bigger end of the supplied
strip
standard connector.
3
2
Connect the supplied standard connector to
Check the car's wiring carefully and connect
them to the supplied standard connector. the unit.
4
Do the other connections, if applicable.
4
3
1 Antenna To antenna Connect the supplied mounting bolt to the
unit.
2 Rear line out To amplifi er line
4
Place the supplied rubber cushion over the
(right) in (right)
end of the mounting bolt.
3 Rear line out To amplifi er line 5
Slide the unit into the dashboard until you
hear a click sound.=
(left) in (left)
6
Reconnect the negative terminal of the car
battery.
Attach the front panel
Detach the front panel
1
Attach the trim plate.
2
Insert the left side of the panel in the chassis
You can detach the front panel to deter theft.
until it is correctly engaged.
1
Press to release the panel.
3
2
Press the right side of the panel until it is
Pull the panel towards you to detach it from
locked into place.
the chassis.
3
Store the panel in the supplied carry case to
protect it from dirt or damage.
Mount into the dashboard
Turn on
Note
1
• Check wire connection before you mount the Press to turn on the unit.
• To turn off the unit, press
unit into a car.
• If preset radio stations are lost when the seconds.
ignition key is turned OFF and then back ON,
Set clock
reconnect the red leads crosswise to the
yellow ones.
1
Press MENU / DISP for 3 seconds.
2
1 Press DBB or SEARCH repeatedly until
Ensure that car dashboard opening is within
the currently clock is displayed.
these measurements:
3
Turn in clockwise direction to set hour.
• If the car dashboard is bigger, the sup-
Turn in anti-clockwise direction to set
plied mounting sleeve is not suitable for
minute.
the car. Remove the mounting sleeve
4
with the removal keys and consult a Press to confi rm.
professional for advice.
2
If the car does not have an on-board drive
View clock
or navigation computer, disconnect the nega-
tive terminal of the car attery.
1
• If you disconnect the car battery in
Press MENU / DISP repeatedly until the clock
a car that has an on-board drive or is displayed.
navigation computer, the computer may
lost its memory.
Tune to a radio station
• If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
1
wires do not touch each other. Press SOURCE to select Tuner.
2
Press DBB or SEARCH to select band:
[FM1] , [FM2] , [FM3] , [AM1] , or [AM 2] .
3
Press LOC/DX to select tuner sensitivity:
[LOCAL] (local): Only station with strong
signal can be broadcast.
[DX] (distance): Stations with strong and
weak signals can be broadcast.
4
Press or to tune to a radio station
manually.
The radio station is broadcast.
»
• To search for radio station automatically,
press or for 3 seconds.
Insert USB device
1
Open the cover marked on the front
panel.
2
Insert the USB device into the USB socket.
The unit star ts playing from the USB
»
device automatically.
Insert SD/MMC card
for 3
1
Open the cover marked on the front
panel.
2
Insert the SD or MMC card into the card
slot.
The unit starts playing from the SD/MMC
»
card automatically.
Control play
To select a folder, press DBB or SEARCH
•
.
• To skip to a track, press or .
• To search within a track, press or for
3 seconds.
• To pause, press 1 , . To resume, press 1 ,
again.
5
6
7