Table of Contents
Advertisement
1.Specifications
Cable Required:
Between transmitter and receiver(s): Category 5 shielded or
unshielded twisted pair (STP or UTP)
Compliance:
CE; FCC Class A, IC Class/classe A
Video Support:
VGA, SVGA, XGA, XGA-2, RGBHV, RGB, YUV
Resolution and
At 500 ft. (137.2 m) or less: Up to 2048 x 1536 at up to 75 Hz;
Refresh Rate:
See the Maximum Distance specification
Transmission:
Transparent to users (automatic, no delay)
Required Source
Video OUT: 75 ohms;
Impedance:
Audio OUT (if any): 600 ohms maximum
Destination
Video IN: 75 ohms;
Impedance:
Audio IN (if any): 600 ohms minimum
Bandwidth:
Video (3 dB): DC to 8 MHz
Audio
Characteristics:
Channels: Stereo, line level
Serial
Characteristics:
Protocol: Asynchronous; transparent to data format;
transparent to data rates up to 19.2 kbps;
Operation: Simplex or full duplex,
user-selectable;
Maximum
Total end to end, from source device to farthest destination
Distance:
device, over good CAT5 cable (assuming A/V source
outputs signal at normal strength):
Up to 500 ft. (152 m) at resolutions up to 2048 x 1536 at up to 75 Hz;
Connectors:
AC1060A: (1) 4 captive screw, (1) RJ-45, (1) HD15 F;(1) DB9 M
AC1061A: (1) 4 captive screw, (1) RJ-45, (1) HD15 F;(1) DB9 M
AC1062A: (1) 4 captive screw, (2) RJ-45, (1) HD15 F;(1) DB9 M
AC1065A: (1) 4 captive screw, (1) RJ-45, (1) HD15 F;(1) DB9 M
AC1066A: (1) 4 captive screw, (2) RJ-45, (1) HD15 F;(1) DB9 M
All: (1) power inlet
Temperature
Operating: 32 to 104°F (0 to 40°C);
Tolerance:
Storage: -4 to +140°F (-20 to +60°C)
Humidity
Tolerance:
Up to 80% noncondensing
Enclosure:
Steel
Power:
From utility-power (mains) outlet to power inlet, through
detachable external power supply: Input: 100 to 250 VAC
@ 50 or 60 Hz (autosensing);
Output: +5 VDC;
Consumption: 5 watts maximum
Size:
AC 1060A: 1.2"H x 4.1"W x 4.3"D (3.1 x 10.4 x 10.9 cm)
AC1061A, AC1062A, AC1065A, AC1066A:
1.2"H x 4.1"W x 5.5"D (3.1 x 10.4 x 14.0 cm)
Weight:
1.0 lb. (0.45 kg) (all units)
CHAPTER 1: Specifications
3
CAT5 MULTI VIDEO SYSTEM.
2. Introduction
2.1 Overview
The CAT5 Multi Video System extends VGA or Component video signals as well as
stereo audio and RS232 signals over ordinary Category 5 cable. All models support
RGBHV, RGB, VGA, and component video, and they use a transmitter-to-receiver
setup. They can be used as video splitters as well as video extenders.
This manual covers CAT5 Multi Video System Transmitter/Receivers (AC1060 -
AC1062A, AC1065A-AC1066A).
These models enable you to broadcast line-level mono audio and RS232 serial, along
with video from your computer, to as many as 100 computer monitors up to 500 feet
(152 m) away over CAT5.
CAT5 Multi Video System receivers are available with single or dual daisychainable
connections. The dual daisychainable receiver is used when the same signal is
distributed to multiple display devices across a single CAT5 cable in a daisychain or
loop-through fashion. Setup and cabling are the same as the single-port receiver.
All models support refresh rates/resolutions up to 2048 x 1536 @ 75 Hz at up to
500 feet (152 m).
This equipment is not intended for, nor does it support, distribution
through an Ethernet network. Do not connect these devices to any sort
of networking or telecommunications equipment!
2.2 Package Contents
You should have received the following when ordering a CAT5 Multi Video System
receiver:
• The transmitter or receiver.
• External power supply (100–250 VAC, 50–60 Hz, autosensing) with cord.
• This manual.
4
WARNING
Advertisement
Table of Contents
