Table of Contents
Advertisement
Quick Links
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES
Wall Mount w/ 8" arm and a screen pan and tilt head
Wall Mount w/ 8" arm and a Universal Printer Mounting Tray
Dual Wall Mount w/ 2- 8" arms, a screen pan and tilt head, and a
Universal Printer Mounting Tray
80000
info@practicalqualitysystems.com
80002
WW.PRACTICALQUALITYSYSTEMS.COM
Page 1 of 15
PN 80000
PN 80002
PN 80003
80003
(818) 993-1022
Document Number:10010901-UM
Advertisement
Table of Contents
Related Manuals for PQS 80000
Summary of Contents for PQS 80000
- Page 1 Page 1 of 15 PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Wall Mount w/ 8” arm and a screen pan and tilt head PN 80000 Wall Mount w/ 8” arm and a Universal Printer Mounting Tray PN 80002 Dual Wall Mount w/ 2- 8” arms, a screen pan and tilt head, and a...
-
Page 2: Table Of Contents
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 2 of 15 TABLE OF CONTENTS TABLE OF FIGURES ............................3 1.1 Identifying, configuring and locating the mount for your application ...............4 1.2 Basic installation steps ...........................4 2.1 Installing the mounting plate on a WALL either horizontally or vertically............4 2.2 Reattaching the arms to the mounting plate installed on a WALL either horizontally or vertically....5 3.1 Installing the mounting plate FLAT on top of a horizontal surface..............5 3.2 Reattaching the arms to the P1 or P3 mounting plate installed FLAT on top of a horizontal surface.....5... -
Page 3: Table Of Figures
Figure 5 - Wall Mount w/8" arm and a Universal Printer Mounting Tray PN 80002..........13 Figure 6 - Wall Mount w/8" arm and a screen pan and tilt head PN 80000 ............14 Figure 7 - Dual Wall Mount w/2 - 8" arms, a screen pan and tilt head, and a Universal Printer Mounting Tray PN 8003................................15... -
Page 4: Identifying, Configuring And Locating The Mount For Your Application
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 4 of 15 1.1 Identifying, configuring and locating the mount for your application PLEASE NOTE: these instructions are for multiple Wall Mount product assemblies, refer to the “List of Figures” page to locate an exploded view of the assembly that you are using. All of these assemblies either include the P1 mounting plate which supports one arm, or the P3 mounting plate which can support either one or two separate arms (See Figures 1, 2 and 3). -
Page 5: Reattaching The Arms To The Mounting Plate Installed On A Wall Either Horizontally Or Vertically
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 5 of 15 2.2 Reattaching the arms to the mounting plate installed on a WALL either horizontally or vertically 1. The SB brackets should still be attached to the ends of the arms. Hold the arm so that the five point knob is on top of the SB bracket. -
Page 6: Basic Steps For Mounting A Screen With Vesa Standard Mounting Holes
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 6 of 15 4.1 Basic steps for mounting a screen with VESA standard mounting holes 1. Remove the pan and tilt head from the end of the arm. 2. Remove the arm assembly from the mounting plate. 3. -
Page 7: Adjusting The Side To Side Position Of A Pan And Tilt Head Or Universal Printer Mounting Tray (Upmt)
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 7 of 15 5. Hold the five pointed knob so that the threaded shaft is pointing up and it is under the end of the arm. Guide the knob shaft up through the hole in the end arm and through the anti slip washer until it contacts the center of the threaded hole in the bottom of the pan and tilt head or UPMT. -
Page 8: Adjusting The Side To Side Position Of The Arms
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 8 of 15 1. Support the entire weight of the screen. Doing one at a time, carefully loosen the locking screws until only three threads of the end of the screw shaft can be seen protruding through the metal next to the anti-slip washer. -
Page 9: Attaching The Mounting Plate To A Pole
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 9 of 15 8.1 Attaching the mounting plate to a pole The P1 or P3 mounting plate can be attached to any 1 ½” or smaller OD (Outside Diameter) tube with U bolts for ceiling or pole mounting. Obtain two U bolts that have a ¼” OD diameter shaft, and are 2” wide center to center. -
Page 10: Figure 1 - P1 And P3 Mounting Plates And Positions
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 10 of 15 Figure 1 - P1 and P3 mounting plates and positions Figure 2 – A P1 mounting plate with one 8" arm info@practicalqualitysystems.com WW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022 Document Number:10010901-UM... -
Page 11: Figure 3 - P3 Mounting Plate With Two 8" Arms
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 11 of 15 Figure 3 - P3 mounting plate with two 8" arms info@practicalqualitysystems.com WW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022 Document Number:10010901-UM... -
Page 12: Figure 4 - One 8" Arm And A Vesa Pan And Tilt Head
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 12 of 15 Figure 4 - One 8" arm and a VESA pan and tilt head info@practicalqualitysystems.com WW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022 Document Number:10010901-UM... -
Page 13: Figure 5 - Wall Mount W/8" Arm And A Universal Printer Mounting Tray Pn 80002
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 13 of 15 Figure 5 - Wall Mount w/8" arm and a Universal Printer Mounting Tray PN 80002 info@practicalqualitysystems.com WW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022 Document Number:10010901-UM... -
Page 14: Figure 6 - Wall Mount W/8" Arm And A Screen Pan And Tilt Head Pn 80000
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 14 of 15 Figure 6 - Wall Mount w/8" arm and a screen pan and tilt head PN 80000 info@practicalqualitysystems.com WW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022 Document Number:10010901-UM... -
Page 15: Figure 7 - Dual Wall Mount W/2 - 8" Arms, A Screen Pan And Tilt Head, And A Universal Printer Mounting Tray Pn 8003
PRODUCT MANUAL FOR WALL MOUNT SERIES ASSEMBLIES Page 15 of 15 Figure 7 - Dual Wall Mount w/2 - 8" arms, a screen pan and tilt head, and a Universal Printer Mounting Tray PN 8003 info@practicalqualitysystems.com WW.PRACTICALQUALITYSYSTEMS.COM (818) 993-1022 Document Number:10010901-UM...
Need help?
Do you have a question about the 80000 and is the answer not in the manual?
Questions and answers