Subscribe to Our Youtube Channel
Related Manuals for MX Atmos Select Serie
Summary of Contents for MX Atmos Select Serie
- Page 1 INSTALLATION & OPERATING INSTRUCTIONS Atmos Select (3 Way Thermostatic Concentric Mixer Valve with Riser Rail & Overhead) Customer Care - 0845 505 2211 MX Atmos Select 6752B 09_14_GF.indd 1 24/10/2014 14:56...
-
Page 2: Safety Warnings
INTRODUCTION This book contains all the necessary fitting and operating instructions for your MX thermostatic mixer shower. Please read these instructions carefully. Read through the whole of this book before beginning your installation. The shower installation MUST be carried out by a suitably competent person after reading these instructions. -
Page 3: Site Requirements
In the event of failure of cold water system, the valve automatically reduces the flow of hot water to prevent scalding. It will only operate again once the flow of cold water has been resumed. MX Atmos Select 6752B 09_14_GF.indd 3 24/10/2014 14:56... -
Page 4: Installation
150mm centers. If installing into a stud partition etc, the pipework and the valve will need support. Before fitting the mixer valve flush out the pipework in accordance with Water Regulations Advisory Service (www.wras.co.uk). MX Atmos Select 6752B 09_14_GF.indd 4 24/10/2014 14:56... -
Page 5: Siting Of The Shower
Riser Rail Handset Height Adjuster Handset Height Adjuster Select Mixer Select Mixer Valve Valve COLD Wall Outlet Wall Outlet Double Double Interlock Interlock 1.5m Hose 1.5m Hose Atmos Select Square Atmos Select Round MX Atmos Select 6752B 09_14_GF.indd 5 24/10/2014 14:56... - Page 6 You should measure the distance between the outlets on the mixer valve you are fitting to determine the exact distance. At this point you may wish to fit the pipework and the wall arm (See wall arm fitting and wall outlet) prior to any tiling. MX Atmos Select 6752B 09_14_GF.indd 6 24/10/2014 14:56...
- Page 7 Fit the on/off control knob onto the diverter (the top shaft with the ‘off’ at the bottom), push fully onto the shaft. Hold firmly in position and tighten the grub screw with allen key supplied (See Fig 10a/b). Square Style Round Style MX Atmos Select 6752B 09_14_GF.indd 7 24/10/2014 14:56...
- Page 8 If replacement riser fix and screw into existing hole. If new installation ensure the hole position is vertically aligned and mark the wall. Unclamping the lower bracket and remove the rail then drill and plug the wall. MX Atmos Select 6752B 09_14_GF.indd 8 24/10/2014 14:56...
- Page 9 (See Fig 8 & 9) Replace the rail assembly through the lower bracket refit the top bracket ensure the slot or indent in the rail is located into the bracket notch and fix to the wall. MX Atmos Select 6752B 09_14_GF.indd 9 24/10/2014 14:56...
- Page 10 (See Fig 11a & 11b), carry out a leak test. MX provide an eco flow controller with every handset they sell. This reduces the flow of water at high water pressures. If you require, fit between the handset & the hose.
-
Page 11: Suggested Action
Turn temperature control temperature. clockwise. D Cold water supply blocked. Turn off shower and consult a competent plumber. Reduce the simultaneous E High volume of cold water drawn demand from the supply. off elsewhere. MX Atmos Select 6752B 09_14_GF.indd 11 24/10/2014 14:56... - Page 12 A Running pressure in excess of 4. Shower valve. maximum recommended. controls noisy whilst in use. Renew flow control cartridge A Flow control cartridge worn. 5. Shower will see parts list. not shut off. MX Atmos Select 6752B 09_14_GF.indd 12 24/10/2014 14:57...
-
Page 13: Components List
Marleton Cross Limited and its subsidiaries (“MX Group”) hope you are satisfied with your purchase and in the unlikely event that you encounter a problem which is caused exclusively by MX Group manufactured product (the “product”) we will take responsibility on the terms set out here. - Page 14 Total loss of the product due to non-availability of parts or other reason, (MX Group will maintain stocks of spare parts for repair for at least 5 years from end of product line to cover this guarantee).
- Page 15 This guarantee applies only to the product itself and any liability on behalf of MX Group is limited to the cost of the product. If a product is deemed to be of faulty manufacture MX Group will at their discretion replace or repair the product.
-
Page 16: Spare Parts
SPARE PARTS In the event that parts or maintenance is needed outside the guarantee MX will endeavour to help with this. Spare parts codes are given in the fitting instructions. By calling the Customer Care Department on 0845 505 2211 with the part number, they will be able to quote you to supply these parts, usually via our spare parts distributor.
Need help?
Do you have a question about the Atmos Select Serie and is the answer not in the manual?
Questions and answers