Safety Advice; Before Assembly; Optional Accessories; During Assembly - Palram Yukon Shed 11x9 Manual

IMPORTANT
Please read these
instructions carefully before you start to assemble this product.
Please
carry out the
steps in
the order
set
out
in
these instructions.
Keep these instructions
in
a
safe
place for future reference.
Safety Advice
For safety purposes we
strongly recommend the product to
be assembled by at least
two people.
Some parts may have sharp edges. Please be
careful when handling components.
Always wear gloves, shoes, safety goggles, and long sleeves when assembling or performing any
maintenance on your product.
Do
not attempt to assemble the product
in
windy or wet conditions.
Dispose
of
all
plastic bags safely
-
keep
them out of
reach
of small children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the
product if
you are tired, have
taken drugs, medications or alcohol,
or if you
are
prone to dizzy
spells.
Do
not
lean against or push the
product during construction.
When using
a
stepladder or power tools, make sure you
follow
the manufacturer's safety advice.
Do
not climb or stand on the roof.
Hot items
such as
recently used grills, blowtorches
etc.
must not
be
stored inside the product.
Note:This product must
be
anchored on to
a
leveled surface and solid foundation to
ensure its
stability.
Make sure
that
screws and anchors are
compatible with foundation
type. Make sure
that
there
are no
obstructions between the assembly
area
and the final position.
Before Assembly
Please consult your local
authorities if
any permits are
required prior to constructing the product.
Choose your site carefully before beginning assembly.
The ground surface must be perfectly flat and leveled and have
a
solid base such
as
concrete, asphalt,
deck etc.
Complete
site
preparation before unpacking parts and beginning assembly.
Sort
the parts and check against the content
parts list.
Parts
should
be laid
out
close at hand. Keep all small parts (screws etc.) in
a
bowl
so
they do not get
lost.
The drawings
in
this manual
are
designed for 11'x 9' shed +
3'
Extension
Kit.
Please
note that content list refers only for 11'x 9' shed.
11'x9'
3' Ext.
Kit 11'x 12'
II
111110
Yukon Standard
(11'x
9')
Yukon
+ 3' Ext. (11 x 12')
Yukon + 3' Ext. x2
(11
x 15')
Yukon + 3' Ext. x3
(11
x 18')
Note:
A
I
the extension module steps
are
marked with
a
dashed
outline, should
be
performed during the product's assembly
process.
Optional
Accessories
If
you've purchased the Floor Kit with the product, relevant
steps are marked
with
this icon.
If
yowve assembled the
product without the floor kit and wish to add one, please
refer to the relevant steps
in
the assembly and perform the
necessary
adjustments.
Shelf Kit:
If
you've purchased shelf
kits,
it
is
recommended to insert screws #411
inside the profiles' tracks during the walls'assembly.
Vertical Bicycle Hanger:
Can be
installed once the product
is
fully assembled.
Make sure
the bottom wheel
is
at
floor
level.
During Assembly
When
encountering the information
icon, please refer to the relevant
assembly step for additional comments and
assistance.
This icon indicates
that the installer should
be
inside the product.
MSteps
This
icon indicates that
the installer should be
outside the product.
Step
1: If
you've purchased
a
Floor Kit,
do not assemble profile #8851!
Step 8:
If
you're installing
a
Floor
Kit
for the
11x12 shed,
do not cut floor board
#
8912!
Step 18: Matte
side
of
all
product's panels should
be
facing out!
Use
mild
soap
if needed to
ease
sliding of profiles
& panels.
Step 21:
It
is
recommended to insert
screws #411
as
preparation for mounting
shelves.
If you've purchased
a
shelf kit,
mount
a
maximum of
2
shelves per post.
Step 30: Before
inserting the
screws, make sure the internal metal profiles are not
protruding
and are well connected
with
one another inside the aluminum profiles.
Step 41: Slow down and be careful when sliding the panels in.
Step 44: Make
sure
the distance between the wall's aluminum profiles and gutter
is
identical prior to tightening the
screws on
the inside.
Step 61: Make
sure
the shed
is
leveled prior to anchoring it to the surface of your choosing.
Use
suitable
screws
and plugs (not supplied).
* Tighten
all screws
when completing assembly.
Do
not tighten
screws and nuts (411 & 466)
until completion of assembly
process.
These
2
icons
indicate if
screws'
tightening
is
required or not.