Advertisement
Quick Links
Advertisement
Related Manuals for ZEHUS BIKE+
Summary of Contents for ZEHUS BIKE+
- Page 1 BIKE+ all in one User manual...
- Page 2 This page was intentionally left blank...
-
Page 3: Safety Notes
Vapors can escape in case of damage or improper use of the BIKE+ all in one. Avoid contacts with those vapors, as they can irritate the respiratory system. Charge the battery pack only with original Zehus battery charger. Damage can occur while using non-original charging devices. - Page 4 IF your BIKE+ all in one has a 6-pin connector (see Figure 1), please be careful to insert the 6-pin charger plug in the 6-pin connector in the proper way. Otherwise short circuits can occur. Warranty is void if charger is not inserted correctly. Do not short circuit the pinout of the charging connector.
-
Page 5: Intended Use
1. Getting started with BIKE+ all in one 1.1 Intended use BIKE+ all in one is intended to be used exclusively with the bike which was sold with. Any attempt to mount BIKE+ all in one on another bike will void warranty claims. BIKE+ all in one is not permitted for competition and race use. -
Page 6: Turning Off The System
1.4 Turning off the system BIKE+ all in one automatically turns off when no activities are detected within 2 minutes, in order to reduce the idle battery use. In order to manually turn off BIKE+ all in one, lean the bike vertically or horizontally, as explained in Figure 3 WHEN A SMARTPHONE IS CONNECTED: if the bike is leant, BIKE+ all in one will be de-ac- tivated (for BIKE+ all in one activation see 2.1). - Page 7 2. Riding BIKE+ all in one it is recommended to gather first experience with BIKE+ all in one away from roads with heavy traffic. BIKE+ all in one is an advanced powertrain for e-bikes that helps you in reducing your ped- aling effort.
- Page 8 The generated power depends on several factors including the bike speed, the pedaling speed and the road slope, depending on the selected power mode. The default power mode of BIKE+ all in one is the “turbo” mode. For instructions on how to change the power mode please refer to 5.1 and 5.4.
- Page 9 2.3 Charging BIKE+ all in one (see Figure 6) To charge BIKE+ all in one, simply remove the protection cap from the charging connec- tor (I) and plug in the Zehus charger (2). Then connect the Zehus charger to a power outlet (110~240 V).
- Page 10 2.5 Correct mounting of BIKE+ all in one on the bike Since BIKE+ all in one has a slope sensor inside, it is important to insert it into the rear fork with the right direction. The front of the hub is marked with a small pin drilled on the left shaft.
- Page 11 3. Using a Smartphone with your BIKE+ all in one In order to access all the functionalities of BIKE+ all in one, you would have to connect a smartphone through the bitride-my bike app. 3.1 What is the bitride-my bike app? The bitride app helps you to act smarter during the everyday mobility;...
- Page 12 3.4 How much is the bitride-my bike app? The bitride-my bike app is available for free. 3.5 How do you install the bitride app? Depending on your mobile device, go either to the Apple Store or to Google Play and search for “bitride”...
- Page 13 Launch bitride-my bike Select your device from the list NOTE: If you have an iPhone bitride-my bike will auto-connect to your BIKE+ all in one Settings Bluetooth Blue tooth detectable as “iPhone ZEHUS” Ü Ö ï â á Ö Ü...
- Page 14 Enable 3.7 BIKE+ registration (first use) NOTE: It is highly recommended to perform BIKE+ all in one registration. If you do not register your BIKE+ all in one you will just be able to use it with the “turbo” power mode (for more power modes see 5.5) In order to use your BIKE+ all in one together with bitride, you need to register it using your bitride app.
- Page 15 In order to register your BIKE+ all in one please fill in the registration form in the app welcome screen: Safari 8:08 AM 100% Safari 8:08 AM 100% DEVICE REGISTRATION Choose a name for your bike and a PIN of 4 digit. Done internet connection...
- Page 16 My devices Support Maintenance (this section needs remote authorization by Zehus support) To access the “ride” section tap the hamburger menu on the upper left side of the screen and select RIDE. To access the online dashboard please connect to your BIKE+ all in one by following the instructions in 3.6.
- Page 17 Change displayed information between actual slope and total distance: tap on the displayed value to change between the two information. Access the ride settings (see 5.1 and following) Disconnect from the device: hold the button to disconnect Access the dashboard App menu settings Choose power mode:...
- Page 18 5.1 Using the ride settings (Figure 8) In this sub-section you can select the desired power mode (see also 5.4, 5.5), the amount of regenerative brake (KERS) and the units you prefer to display speed and distance. Furthermore, you can perform the factory reset of your bike by sliding the factory reset icon on the right side of your screen.
- Page 19 5.2 Calibrate the slope sensor on your BIKE+ all in one BIKE+ all in one features an advanced slope sensor that is very important to obtain the correct and pleasant behavior while using some of the power modes (see 5.5). NOTE: please check the calibration of the slope sensor carefully at the first connection.
- Page 20 5.3 Performing a factory reset on BIKE+ all in one In order to perform a factory reset on your BIKE+ all in one, please tap the hyperlink “fac- tory reset” on the dashboard menu. The app will ask you to insert the PIN of your bike to perform the factory reset.
- Page 21 BIKE+ (Figure 15): this power mode is Hybrid and it is sensitive to the road slope (see range 1). This mode is non plug-in: thanks to Zehus patented technology, BIKE+ all in one changes the motor map automatically and continuously in order to keep the battery charged.
- Page 22 5.7 BIKE+ all in one power modes charts Pedalling effort Motor Power -100 Speed [km/h] Figure 10: motor assistance in turbo power mode Pedalling effort Motor Power -100 Speed [km/h] Figure 11: motor assistance in e-bike mode...
- Page 23 Pedalling effort Motor Power Regenerative zone -100 Speed [km/h] Figure 12: motor assistance / regenerative zone in range 1 mode Pedalling effort Motor Power Regenerative zone -100 Speed [km/h] Figure 13: motor assistance / regenerative zone in range 2 mode...
- Page 24 Pedalling effort Motor Power Regenerative zone -100 Speed [km/h] Figure 14: motor assistance / regenerative zone in range 3 mode Pedalling effort Motor Power Regenerative zone -100 Speed [km/h] Figure 15: motor assistance / regenerative zone / battery level sensitivity in BIKE+ mode...
- Page 25 Bike+ all in one correctly, please contact our customer care on our website or at info@ zehus.it! Icons can appear both yellow (warning) or Red (severe risk or damage). The warning icons that can appear on your bitride app in the dashboard are: Temperature WARNING This icon appears when the temperature inside the hub reaches a critical level.
- Page 26 Check warranty and manuals related to your product Check a F.A.Q. section Perform a diagnosis on your All in One and send it to Zehus Support team Send a generic feedback to Zehus Support team 6.1 Sending an online or offline feedback to Zehus Support team When you notice something wrong with your powertrain, it is possible to send a feedback to Zehus support team straight from the app.
- Page 27 The second feedback, also called offline feedback, does not require to be connected to the bike. This generic feedback can be used for questions or in case you can not connect to your BIKE+ all in one to gather diagnostic data. Tap here to check user manual, getting started manual, warranty terms and privacy policy Tap here to check the FAQs on your product...
-
Page 28: Factory Reset
If not set or set in a wrong way, BIKE+ all in one may not work properly. Please contact the Zehus Support team providing the brand and model of your bike, your frame number (if applicable), your BIKE+ all in one serial number. Our support team will then check the information on our server and they will remotely authorize you to use this recovery procedure. - Page 29 8.3 Using the My devices section In this section you can see all the Zehus devices you connected to and set your favorites. For any device you can see: Device type (your device is a bike plus)
- Page 30 8.4 Password and PIN recovery within bitride-my bike When you log out, or when you perform a fresh installation of bitride-my bike you will be asked to log in with your e-mail and password. If you forgot your password, simply tap on “?”.
- Page 31 In case of malfunctioning your battery pack will have to be replaced. Please refer to a Zehus retailer to have your battery pack replaced. Note: when not using the bike for long periods it is recommended to charge the bat- tery pack to 60% and to check the battery condition at least every 6 months.
-
Page 32: Technical Data
Technical data Drive unit Rated power Maximum torque Battery pack Rated Voltage 29.2 Rated Capacity 5300 Energy 154.8 Weight (~) Operating Temperature °C -20°C to +70°C Storage Temperature °C -40°C to +60°C Charging Temperature °C -20°C to +60°C Degree of protection IP54 Charger Voltage Input... -
Page 33: Maintenance And Service
6 on page 26 or send an e-mail to support@zehus.it. When contacting Zehus for an issue related to BIKE+ all in one please provide one of the following information together with the problem description:... -
Page 34: Only For Ec Countries
Inform your parcel service that the package contains dangerous goods. Please also observe the possibility of more detailed national regulations. In case of questions concerning transport of BIKE+ all in one, please refer to an authorized Zehus dealer. Bicycle dealers can also provide suitable transport packaging. 11.4 Disposal BIKE+ all in one and all its components should be sorted for environmental-friendly recy- cling. - Page 35 This page was intentionally left blank...
- Page 36 Please The specifications on this document are subject to change at ZEHUS de- note that the use of this accesso- cision. ZEHUS assumes no responsibility for any claims or damages arising...