Table of Contents
Advertisement
Quick Links
Equipping technicians with heavy-duty products
SHOP PRESS
ASSEMBLY INSTRUCTIONS
212025 - 25 TON MANUAL SHOP PRESS
PRESS SPECIFICATIONS
LEVEL
MODEL
CAPACITY
#
(TONS)
1
212025
25
AmerEquip™ Shop Presses
TM
RAM
THROAT HEIGHT
THROAT
TRAVEL
(IN.)
WIDTH
(IN.)
MIN.
MAX.
6.125
.5
33.5
BED WEIGHT
ADJUSTMENTS (IN.)
(IN.)
QTY.
IN.
35
8
5
1
BETWEEN
BASE
OVERALL
BED RAILS
(IN.)
(IN.)
WIDTH
DEPTH
8
42
29.75
© Copyright 2013, AmerEquip™
SHIPPING
HEIGHT
WEIGHT
(IN.)
(LBS.)
74
513
rev. 06/20/13
Advertisement
Table of Contents
Related Manuals for AmerEquip 212025
Summary of Contents for AmerEquip 212025
-
Page 1: Assembly Instructions
Equipping technicians with heavy-duty products SHOP PRESS ASSEMBLY INSTRUCTIONS 212025 - 25 TON MANUAL SHOP PRESS PRESS SPECIFICATIONS LEVEL MODEL CAPACITY THROAT HEIGHT THROAT BED WEIGHT BETWEEN BASE OVERALL SHIPPING (TONS) TRAVEL (IN.) WIDTH ADJUSTMENTS (IN.) BED RAILS (IN.) HEIGHT WEIGHT (IN.) -
Page 2: Safety Information
• Failure to heed these warnings may result in serious or fatal personal If you are missing any parts or find any damage, call AmerEquip directly at injury and/or property damage. 1-(800) 684-0277. Please do not call the store where you purchased this product. -
Page 3: Parts List
Not needed for assembly 1/2" Nuts - 8 Washers - 8 TOOLS NEEDED 1-1/4" x 14" Press Pins - 4 3/4" and 1/2" sockets and wrenches Examine box contents, then proceed with the following instructions. AmerEquip™ Shop Presses rev. 06/20/13... - Page 4 Slide bed down to bottom of frame Inside of frame Note: Position press feet on each side of the press. Attach one bolt, washer and nut on each side. Bolts should be attached OFFSET from one another. Front view AmerEquip™ Shop Presses rev. 06/20/13...
- Page 5 WARNING Note: When sliding bed to frame Bed must be at the BOTTOM of the frame bottom, DO NOT use bed handles. before proceeding to the next step. Slide bed down to bottom of frame AmerEquip™ Shop Presses rev. 06/20/13...
- Page 6 ALL FOUR (4) pins must be COMPLETELY through BOTH SIDES WARNING of frame in order to operate press. Let bed rest on inserted pins Place 3rd and 4th pin on each side Secure pins completely through bed and frame. AmerEquip™ Shop Presses rev. 06/20/13...
- Page 7 See Step 6. on to mounting the pump assembly. WARNING Hose must be on the OUTSIDE of ram frame, or it will NOT be mountable to the press. AmerEquip™ Shop Presses rev. 06/20/13...
- Page 8 Attach bolts up through ram frame to matching holes in press. Hand tighten. Wrench tighten This end up after both bolts have been installed. Ram is now able to slide left and right within ram frame. AmerEquip™ Shop Presses rev. 06/20/13...
- Page 9 PRESSURE CRADLE. Pump ram Ram will retract as against press plates until gauge against press plates until gauge Do not allow the ram to pressure is released. reads "5 Tons". reads "10 Tons". extend more than 5.5". AmerEquip™ Shop Presses rev. 06/20/13...
-
Page 10: Pump Instructions
CAUTION DO NOT TURN RELEASE VALVE MORE THAN ONE FULL TURN or equipment may be disabled. AmerEquip™ Shop Presses rev. 06/20/13... - Page 11 1. Move press bed into LOWEST position 3. Thread the BARE end of the LONGER so it is resting on top of pins 1 and 2. of the two steel cables up and through DO NOT FULLY TIGHTEN. the pump bracket. AmerEquip™ Shop Presses rev. 06/20/13...
- Page 12 It may be necessary to repeat this leveling with our products. If you are missing any parts procedure in the future. or find any damage, call AmerEquip directly at 1-(800) 684-0277. Please do not call the store where you purchased this product.
-
Page 13: Replacement Parts List
Equipping technicians with heavy-duty products REPLACEMENT PARTS LIST 212025 - 25 TON MANUAL SHOP PRESS ITEM NO. DESCRIPTION QTY. ITEM NO. DESCRIPTION QTY. Press Spring Hose & Fitting † Press Bed Seal Kit for Pump and Ram (not shown) †... - Page 14 SHCS 7/16 14 x 1/2" SHCS 7/16 14 x 3/4" * Light Spring * Heavy Spring 7/16" Split Lock Washer Pump Filter Pump Fitting 1/4" MNPT 7/16" JICF 7/8" Grip Handle for Pump * O-Ring AmerEquip™ Shop Presses rev. 06/20/13...
- Page 15 Equipping technicians with heavy-duty products NOTES AmerEquip™ Shop Presses rev. 06/20/13...
- Page 16 Equipping technicians with heavy-duty products NOTES AmerEquip™ Shop Presses rev. 06/20/13...
Need help?
Do you have a question about the 212025 and is the answer not in the manual?
Questions and answers