DeWalt DCD708 Original Instructions Manual page 13

2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise with
one hand while holding the tool with the other. Your tool is
equipped with an automatic spindle lock mechanism. This
allows you to open and close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve and
one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
Speed Selection (Fig. A)
The tool features two speed settings for greater versatility.
nOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
1. To select speed 1 (high torque setting), turn the tool off and
permit it to stop. Slide the speed selector
from the chuck).
2. To select speed 2 (high speed setting), turn the tool off and
permit it to stop. Slide the speed selector
the chuck).
If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
back position.
Mode Selection (Fig. A)
The mode selection collar can be used to select the correct
6
operating mode depending upon the planned application.
To select, rotate the collar until the desired symbol aligns with
the arrow.
symbol
1–15 Screwdriving (higher number = greater torque)
Hammerdrilling (DCD709 only)
Variable Speed Trigger and Forward/Reverse
Control Button (Fig. A, E)
The drill is turned on and off by pulling and releasing the
variable speed trigger . The farther the trigger is depressed,
4
the higher the speed of the drill. Your tool is equipped with
a brake. The chuck will stop as soon as the trigger switch is
fully released.
A forward/reverse control button
direction of the tool and also serves as a lock-off button.
• To select forward rotation, release the trigger and depress
the forward/reverse control button on the right side of
the tool.
7 back (away
forward (toward
7
Mode
Drilling
5 determines the rotational
• To select reverse, depress the forward/reverse control
button on the left side of the tool.
nOTE: The centre position of the control button locks the tool
in the off position. When changing the position of the control
button, be sure the trigger is released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. C)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the battery pack.
Worklight (Fig. A)
There is a worklight 8 located on the foot of the tool. The
worklight is activated when the trigger switch is depressed.
When the trigger is released, the worklight will stay illuminated
for up to 20 seconds.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Performing an Application (Fig. A, D)

WARNING: To reduce the risk of personal injury,
ALWAYS ensure workpiece is anchored or clamped firmly.

WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
Prior to performing work:
• Set the speed selector 7 . Refer to Speed Selection.
• Install the appropriate bit or accessory into the chuck. Refer
to Installing a Bit or Accessory into a Keyless Chuck.

WARNING:
• Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir flammable liquids
labeled accordingly.
English
3
11