1. Manuals
  2. Brands
  3. Topp Music Gear Manuals
  4. Enclosure
  5. Event Series
  6. User manual

Topp Music Gear Event Series User Manual

Active speaker cabinet class d with dsp
Hide thumbs
Table of Contents

Advertisement

Quick Links

EVENT 2K SYSTEM / EVENT 4K SYSTEM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Event Series and is the answer not in the manual?

Questions and answers

Related Manuals for Topp Music Gear Event Series

Summary of Contents for Topp Music Gear Event Series

  • Page 1 EVENT 2K SYSTEM / EVENT 4K SYSTEM...
  • Page 2 Important Safety Instructions...

  • Page 3: Table Of Contents

    Table of Contents 1. INTRODUCTION 2. INSTALLATION TIPS 3. USEFULL DATA 4. QUICK START 5. CONNECT MANNER 6. BACK PANEL DESCRIPTION 7. DSP CONTROL 7. CONNECTION PLATE SYSTEM 8. WIRE CONNECTIONS 9. TECHNICAL SPECIFICATIONS 10. DSP SOFTWARE CONNECTION / IP CONTROL INSTRUCTION 10.

  • Page 4: Introduction

    Introduction The new cabinets have been designed to provide a cost effective high grade solution while maintainig high quality cabinet construction and optimum components. Our Professional Audio Products are designed and tested by a highly qualified engineering team with more than 20 years of experience.

  • Page 5: Quick Start

    Quick Start When mounting a speaker onto any stand, always ensure that the stand is on a flat, level sur-face, with the legs fully extended. Be sure to check that the maximum load weight for the stands is greater than the weight of the ARRAY SYSTEMS loudspeaker.

  • Page 6: Connect Manner

    Connect Manner EVENT 2K 1. Turn the POLE/SAT-BM/SAT-TP back control switch to “LOCK” position. 2. Place the EVENT 2K on a flat surface and rotate the POLE/SAT-BM/SAT-TP from low to high into the bottom threaded bracket until it is tight. 3.
  • Page 7 Connect Manner EVENT 4K 1. Place the EVENT 4K SUB on a flat surface. 2. Push the SAT from front to back into the SUB connector until it is tight. 3. After the installation is completed, if you need to disassemble, press the “LOCK” button of the SUB connector and push the SAT forward slowly.

  • Page 8: Back Panel Description

    Back Panel Description EVENT 2K / EVENT 4K (11) (12) (13) (10) (14) (15) (16) (17) 1. AC INPUT-The AC connection is established via the IEC connector. The IEC connector is compatible with a lockout power cord (not included). 2. POWER - AC switch for turning the power on or off. When POWER is turned on,the power led lights up and LCD screen lights up.

  • Page 9: Dsp Control

    DSP Control With the integrated DSP control menu, users can select multiple DSP system settings on the speaker. To access the DSP Control menu, follow below steps: 1. Press the MASTER VOL knob and the DSP Control menu will appear. Input Settings Factory Presets User Programs...
  • Page 10 DSP Control MENU The Input Settings menu is used to configure the speaker's input sensitivity control and Delay and Phase control; Input Settings Input Settings Input Settings Are you sure Are you sure HI-Z Switch to High Switch to Mic ? Delay: 0 Feet Resistance ? Phase...
  • Page 11 DSP Control The EQ menu is a 4-band EQ (equalizer) that the user can fine tune in addition to FUNCTION and LOCATION. The options available for this selection are: HI, MD, LM, and LO. Back 12.1K Default: 0 decibels 2.52K Range: -18 decibels –...
  • Page 12 DSP Control The Name menu is the name of the current speaker. This menu allows you to customize the name of the speaker as needed. The Default Settings menu is used to reset the speakers to their original factory settings. The options for this selection are: NO or YES.

  • Page 13: Connection Plate System

    Connection Plate System Make your initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely down. Two Active Subwoofers & Two Passive Satellite Speakers 1) Connect one side of the signal cable to the output of your mixer (left / right) with a TRS or XLR connector and the other side of the cable to the line input (combo) in the active subwoofer (with a TRS to XLR connector).
  • Page 14 Connection Plate System Make your initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely down. 1) Connect one side of the signal cable at your audio mixer into output left / right (with Stereo-Jack or XLR) and the other side of the cable into the line input (Stereo-Jack) of your active speaker cabinet.

  • Page 15: Wire Connections

    Wire Connections...

  • Page 16: Technical Specifications

    Technical Specifications EVENT 2K SYSTEM: SUB+POLE+SAT-BM+SAT-TP EVENT 2K System Frequency Response 40Hz – 20KHz (-10dB) Total Amplifier Power 1000W Con�nuous/2000W Program/4000W Peak Class D @ 4 Ohms Maximum SPL@1M 128dB Crossover Frequency 220Hz Dispersion(-6dB) 120°Horizontal Dimensions(WxHxD) 440 x 2015 x 640mm (17.32'' x 79.33'' x 25.20'') Net Weight 37.81Kg (83.35 Ibs) System Type...
  • Page 17 Technical Specifications EVENT 4K SYSTEM: SUB+SAT EVENT 4K SYSTEM Frequency Response 35Hz – 20KHz (-10dB) 2000W Con�nuous / 4000W Program / 8000W Peak Class D @ 4 Ohms Total Amplifier Power Maximum SPL@1M 134dB Crossover Frequency 200Hz Dispersion(-6dB) 130°Horizontal Dimensions(WxHxD) 460 x 2010 x 676mm (18.11'' x 79.13'' x 26.6'') Net Weight 50.15Kg (110.56 Ibs)

  • Page 18: Dsp Software Connection / Ip Control Instruction

    DSP software connection / IP Control instruction 1. List of required materials Computer（window system7-10）*1 Router*1 Network cable *1 CS PRO_1.09 software*1 EVENT 2K / EVENT 4K SYSTEM *1PCS 2. Connect the router to the module network port and turn on the power. 3.

This manual is also suitable for:

Event 4kEvent 2k

Table of Contents