Page 1
Disc Harrow BDH750 BD7C BDH900 BD9C ATTENTION: ALL WARRANTY WORK MUST BE APPROVED BY BROWN MFG. CORP. BEFORE WORK BEGINS Owner/Operator Manual WARNING Before operating your machine, stop and read this owners manual. Do not attempt to operate the unit until you fully understand the material covered in this manual.
The obligation of Brown shall be limited to replacing or repairing the detective product, at the option of Brown. Brown shall not be responsible for any labor or cost of removal or repairing or reinstallation of its products and shall not be liable for transportation costs to and from its plant in Ozark, Alabama.
D a t e P u r c h a s e d , a n d Dealer Information for future Serial No.: _______________________ reference. For further information: Date Purchased: ____/____/_____ Brown Manufacturing Corp. 6001 E. Hwy 27 Dealer: __________________________ Ozark, AL 36360 Phone: (334) 795-6603 Toll Free: (800) 663-8909 FAX: (334) 795-3029 www.brownmfgcorp.com...
Equipment Safety Warning: Read this manual before operation. Operators of the equipment must read and understand this manual. Failure to read this manual and follow these safety and operating instructions could result in serious bodily injury or even death. WARNING Before operating your machine, stop and read this owners manual.
Page 8
Unauthorized modifications to the equipment are not recommended. This could impair the function, safety, and life of the machine. • For any part of this manual that you do not understand, contact your dealer or Brown Manufacturing Corporation at (800) 633-8909. •...
Page 9
Equipment Safety Safety Decals The following safety decals should be attached to the equipment at all times. Should any decal become damaged or lost, it is the responsibility of the owner to replace it. Additional decals may be obtained from the manufacturer. WARNING ADVERTENCIA Antes de probar la unidad por primera vez...
Page 10
Equipment Safety Warning! Transport with WARNING care. Transport with care. Use slow-moving Before transporting to a new location, make certain vehicle emblem that the slow-moving vehicle (SMV) emblem is and flashing light. installed and is clearly visible. Use flashing lights Follow local and follow local traffic regulations.
Page 11
Equipment Safety Warning! Transport with WARNING care. Transport with care. Before transporting to a new location, make Use slow-moving certain that the slow-moving vehicle emblem is vehicle emblem installed and is clearly visible. Use flashing lights and flashing light. and follow local traffic regulations. Follow local traffic regulations.
Page 13
Assembly 3/4” x 5 1/2” Model Proper Gang Arm Length BDH-600 (front) 29” gang arm BDH-600 (rear) 36” gang arm BDH-750 (front) 40” gang arm BDH-750 (rear) 46” gang arm BDH-900 (front) 46” gang arm BDH-900 (rear) 54” gang arm BDH-1100 (front) 58”...
Assembly/Quick Hitch Brown Disc Harrows Brown Disc Harrows come fully assembled, please check all fasteners to ensure correct torque before use and after two hours of use. A-frame assembly Step 1: Bolt A-frame braces to the outside of the top of A-frame in the back holes.
Operation Before hitching harrow to your tractor, make sure all safety devices are installed on the tractor. STOP Please follow all safety instructions and procedures. Attach equipment to tractor. Be sure the tractor is equipped with the correct category hitchpins, top link, etc. Be extremely careful when positioning tractor to hitch to the equipment.
Troubleshooting Problem Possible Cause(s) Possible Solution(s) 1. Excessive Speed 1. Reduce speed Leaving center ridge 2. Rear gangs cut too deep 2. Reduce gang angle 3. Top link too long 3. Shorten top link 1. Insufficent speed 1. Increase speed Leaving center valley 2.
Replacement Parts Ordering replacement parts Please contact the nearest Brown dealer for replacements parts. They will be able to meet most of your equipment needs.
Page 21
18” 7 Guage Disc Blade DH-116-20 20 “ 7 Guage Disc Blade DH-116-22 22”7 Guage Disc Blade Ordering replacement parts Please contact the nearest Brown dealer for replacements parts. They will be able to meet most of your equipment needs.
Page 22
3 per Hanger Assy Bolt, 5/8” X 6 1/2” NC GR5 For Bearing Hangers DH-1254B Bearing Hanger Assembly Ordering replacement parts Please contact the nearest Brown dealer for replacements parts. They will be able to meet most of your equipment needs.
Page 23
Replacement Parts Ref. No. Part No. Description DH-1254A 1 per Hanger Assy Bearing Hanger Spacer DH-128 36” gang arm for BDH-600 (rear) DH-129 29” gang arm for BDH-600 (front) DH-130 46” gang arm for BDH-750 (rear), BDH-900 (front) DH-131 40” gang arm for BDH-750 (front) DH-132 54”...
Page 24
Replacement Parts See Page 16 for Assembly Instructions of Scrapers Balk Breaker Assembly and Parts Breakdown...
Page 25
Replacement Parts Ref. No. Part No. Description DH-900-A6 Furrow filler extension DH-197 U-Bolt (1/2” x 4” x 4”) DH-196 U-Bolt (1/2” x 1 1/2” x 1 3/4”) DH-198 Scraper bar holder DH-600-50 30” scraper bar for BDH-600 DH-750-03 38” scraper bar for BDH-750 DH-900-109 48”...