Hammond Leslie CU-1 Owner's Manual



Attaching the CU-1 to the keyboard

For your safety, please operate your Hammond prod-
uct on a level, stable surface.
1. Attaching the CU-1 unit.
 SK2, XK-1C, XK-3, XK-3C (Thin bottom of the Keyboard)
Remove the protective paper from the adhesive tape on the thick spac-
er, and attach the spacer to the CU-1 unit as shown above.
 XLK-3, XLK-5 (Middle bottom of the Keyboard)
Remove the protective paper from the adhesive tape on the thin spac-
er, and attach the spacer to the CU-1 unit as shown above.
 #920, A-162, A-405, XK-5 (Deep bottom of the Keyboard)
No spacer is needed for mounting the CU-1 Unit.
 Line up the screws attached to the CU-1 unit with the pair of chosen
holes located on the bottom side of the front rail and securely tighten
these screws.
NOTE: Do not place the keyboard with the CU-1 unit attached onto a fl at
desk type surface. Since the CU-1 extends past the bottom of the
keyboard, the CU-1 unit and front rail of the keyboard could be
seriously damaged.
NOTE: Before placing your XK-3/3C into an ATA keyboard type case, make
sure you remove the CU-1 unit fi rst.

2. Connecting to the equipment

 #920, A-162, A-405, SK2, XK-1C, XK-3, XK-3C, XLK-3
Insert the plug on the CU-1 into the equipment labeled "Foot Switch"
jack.
 XK-5, XLK-5
Insert the plug on the CU-1 into the equipment labeled "CU-1" jack.
For other compatible model, see owner's manual of your instrument
which attach the CU-1 for detail.

LESLIE SWITCH
Th ank you and congratulations on your purchase of the Ham-
mond CU-1 Leslie switch. Th e lever switch on the "Half-
Moon" shaped CU-1 unit is used to control the Leslie eff ects
just like on the original B-3. Please read the installations in-
structions carefully before you install the CU-1.
 #920, A-162, A-405, XK-3, XK-3C, XLK-3
 SK2, XK-1C
 XK-5, XLK-5
 #920, A-162, A-405, XK-3, XK-3C
 SK2, XK-1C, XK-5
Owner's Manual

Setting up to allow the CU-1

 Turn on the equipment, touch the [MENU], [4]Control and choice
the "FOOT SW" page using [PAGE] buttons.
 Select "CU-1" using [VALUE] buttons.
 Turn on the equipment, touch the [MENU], [][][]Control and
choice the "FOOT SW" page using [] []buttons.
 Select "CU-1" using [VALUE] knob.
No operation required.
For other compatible model, see owner's manual of your equipment
how to set up the CU-1.

Playing with your CU-1 Switch

 CHORALE:
Th e Leslie eff ect is "On", rotation mode is "Slow. "
 TREMOLO:
Th e Leslie eff ect is "On", rotation mode is "Fast. "
 STOP:
1) Th e rotation stops, the Leslie eff ect is still "ON", if the
[BRAKE] button is "On" (XK-3/3C) or Off Mode is at "Brake"
(#920, A-162, A-405).

2) Th e Leslie eff ect is "Off ", rotation continues, if the [BRAKE]
button is "Off " (XK-3/3C) or Off Mode is at "Th rough" (#920,
A-162, A-405).

It takes a moment for the equipment detecting STOP position,
to make the switching between CHORALE and TREMOLO
smoothly.
 CHORALE:
Th e rotation mode is "Slow. "
 TREMOLO:
Th e rotation mode is "Fast. "
 STOP:
Th e rotation stops. It takes a moment for the equipment de-
tecting the STOP position, to make the switching between
CHORALE and TREMOLO smoothly.

It switches only the rotation. To switch "On" or "Bypass" the
Leslie eff ect (switch Rotary or Stationary channel), press the
[BYPASS] button.
NOTE: On newer Hammond products, the speeds of the Leslie can also
be selected by means of a kick switch on the expression pedal or a
switch button on the product itself. Thus the selected speed on the
CU-1 unit may occasionally not match the action speed (slow-fast-
off ) of the Leslie. If this occurs, simply move the lever switch on the
CU-1 to the adjacent position and the actual rotor speed will then
match the CU-1 selection.

Manufacturer:

SUZUKI MUSICAL INSTRUMENT MFG. CO., LTD.
25-12, Ryoke 2 Chome, Naka-ku,
Hamamatsu 430-0852 (Shizuoka)
Purchased items:

CU-1 unit

(w/2 Thumb screws) ..........1
Spacer (thick) .......................1
Spacer (thin) .........................1
JAPAN