Advertisement
From the Energy Screen, press Gauge Setting. Configure the gauge
5
settings that will be displayed on the Home Screen.
Press ok.
6
From the Energy Screen, press Monitor. Ensure that the energy
7
monitor is displaying real‐time data. The data should update every
12 seconds.
From the Energy Screen, press History. Show the end‐user that
8
they can view their energy consumption by day, week, month and
year.
When you are
9
finished entering
the gauge settings,
the Home Screen
will alternately
display the date/
time and either the
KW per/hour or
the cost per/hour.
Specifications*
Z‐Wave chip
300 Series
Software
5.0x
Operational
120VAC, 60 Hz
Voltage
Range
Up to 100 feet line of sight between the Controller
and/or closest Z‐Wave Receive module
Frequency
908.42MHz
Maximum Load Incandescent: 600W Max, 120VAC
Resistive: 15 amps (1800 watts ) Maximum 120VAC
Motor: 1/2 H.P. Max, 120VAC
*For Indoor Use Only
©2013 2GIG by Linear Corporation. All Rights Reserved.
2
REGULATORY INFORMATION
FCC ID: KFR-ZBRG433
INDUSTRY CANADA ID: 3318A-ZBRG433
This device complies with Part 15 of the FCC's Rules. Operation is
subject to the following two conditions:
1
This device may not cause harmful interference
2
This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This product complies with FCC radiation exposure limits for an
uncontrolled environment. Avoid operating this product at a distance
less than 20cm from user.
CAUTION: Any changed or modifications not expressly
approved by the party responsible for compliance could void
the user's authority to operate this equipment.
Limited Warranty
This 2GIG Technologies product is warranted against defects in
material and workmanship for 1 year. This warranty extends only to
wholesale customers who buy direct from 2GIG Technologies or
through 2GIG Technologies' normal distribution channels. 2GIG
Technologies does not warrant this product to consumers. Consumers
should inquire from their selling dealer as to the nature of the dealer's
warranty, if any.
There are no obligations or liabilities on the part of 2GIG Technologies
for consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to
loss of property, revenue, or profit, or cost of removal, installation, or
reinstallation. All implied warranties for functionality, are valid only
until the warranty expires. This 2GIG Technologies Warranty is in lieu
of all other warranties expressed or implied.
For technical support in the USA and Canada:
855‐2GIG‐TECH (855‐244‐4832)
Email: techsupport@2gig.com
Internet: dealer.2gig.com
Visit web site for technical support hours of operation
For technical support outside of the USA and Canada:
Contact your regional distributor
Visit dealer.2gig.com for a list of distributors in your region
PN: 77‐000199‐001 Rev. A
Advertisement
