Quick Sweet 16 EP Manual
  1. Manuals
  2. Brands
  3. Quick Manuals
  4. Toy
  5. Sweet 16 EP
  6. Manual
Quick Sweet 16 EP Manual

Quick Sweet 16 EP Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
QuickWorldwide.com
Exclusively distributed by:
Quick worldwide
201 South 3
rd
. St. & 309 N.
Coopersburg, PA 18036
Phone: (610)-282-4811
Fax: (610)-282-4816
Sweet 16 EP Helicopter
Websites:
http://www.hhiheli.com
http://www.quickheli.com
http://www.giantscaleplanes.com
E-mail:
hhi@fast.net
Jon@quickworldwide.com
(Tech. Support)

Advertisement

Table of Contents
loading

Related Manuals for Quick Sweet 16 EP

Summary of Contents for Quick Sweet 16 EP

  • Page 1 QuickWorldwide.com Sweet 16 EP Helicopter Exclusively distributed by: Websites: Quick worldwide http://www.hhiheli.com http://www.quickheli.com 201 South 3 . St. & 309 N. http://www.giantscaleplanes.com Coopersburg, PA 18036 E-mail: hhi@fast.net Phone: (610)-282-4811 Jon@quickworldwide.com Fax: (610)-282-4816 (Tech. Support)

  • Page 2: Pre-Assembly Information

    Quick Pre-Assembly Information Quick Worldwide & Hobbies & Helis International: Quick of Japan and Hobbies & Helis International teamed up to make parts 6 years ago. In the beginning, our specialty was the manufacturing of various upgrade parts for many of the plastic helicopters on the market.
  • Page 3 8. Control Linkages: The control linkages that are provided with the Quick Kit are high quality 2.3mm stainless steel rods and the rod ends are made of a high quality Delrin. 9. Single Blade Axle Design: The single blade axle design is simple...
  • Page 4 Tools Needed to Assemble the helicopter. Ball End Drivers Phillips Screw Driver Bubble Blade Balancer HHI7050 HHI7010 High Point Balancer DUB499 Pitch Gauge HHI7001 HHI7320 – 6pc Nut & Allen Driver Set Piston Head Lock HHI7020 Composite Paddle Universal Flybar Lock Gauges HHI7040 HHI7000...
  • Page 5 Hardware & Accessories Engine (Recommended Motor but others will work) Aveox 36/38/3 Glues & Thread Lockers JB Weld…JBW8265S Locktite. …….PT40 Ca Glue. …GBG1 Radio Mounting Accessories Single Sided Foam Tape… HHI2008 Receiver Hold Down Straps HHI55** $4.99 2 Per Bag & Colors: Red, White, Purple, Black Receiver Strong Box…...
  • Page 6 Other Optional Accessories 3mm Fly-bar Stiffeners…HHI402* Quickie Servo Arm Set 3mm Finishing Caps HHIM1110 Available in Blue, Silver, Gold, & Purple Base Load Antenna HHI53** Available in Blue, Gold, Purple & In 40, 50, 72mhz...

  • Page 7: Section 1 - Frame Assembly

    Radio Requirements Radios: Hobbies & Helis & its distributors carry various lines of helicopter radios. Any radio that supports EMS/CCPM Mixing will work fine. We recommend using an eight-channel or better radio, although a six channel radio is all that is required. Servos: This is the single most important function of the helicopter.
  • Page 8 Assemble the main frames as shown in the picture. The bearing blocks will be inserted as follows; the upper block will have the open part (Flush side)facing up, and the lower bearing block will have the open face down. Each of the bearing blocks are attached with (4) M3x6 cap head screws.

  • Page 9: Landing Gear Installation

    Attach the antirotation upright piece to the antirotation base using (2) M3x6 cap head screws. Attach the antirotation guide using (4) M3x6 cap head screws and (4) M3 washer. Assemble the rear sub-frame as shown. Attach the two frame halves with the boom holders. They will be attached using (4) M3x35 cap head bolts and nuts Next you will attach the rear...
  • Page 10 Locate (2) Landing Gear Struts place a piece of masking tape across top and Center helicopter on the struts and mark holes Replacement Part #: Landing Gear Set – HHI4007 Drill (4) M3 holes at the previously determined locations. After holes have been Drilled remove tape.

  • Page 11: Section 2 - Main Gear Installation

    Install (2) Skid Pipes into the struts so the Helicopter is adequately balanced and secure using (4) M3 Set Screws. Install (4) Skid pipe end caps using medium CA glue. Section 2 – Main Gear Installation Parts List Main Shaft Collar x 1 Bag 2 M3x18 Cap Head Screw x 1 Main Gear...

  • Page 12: Section 3 - Counter Gear Assembly

    Slide the main shaft down through the autorotation hub. Secure it in place with an M3x18 cap head bolt and M3 locknut. Then secure the main shaft on top with the main shaft collar and (4) M3x3 set screws. This is how the helicopter should look at this point.
  • Page 13 Secure the gear in place using an E-clip. Locate the two counter gear bearing blocks. Next slide each bearing block onto the counter gear shaft. Each bearing block has an open face. The open faces should both face up as shown in the picture.

  • Page 14: Section 4 - Control Items

    Next, slide the counter gear assembly into the frame and secure it in place using (8) M3x6 cap head screws with a washer under each. At this point, your helicopter should look like this. Section 4 – Control Items Parts List Swashplate M2x12 Pan head screw x 2 Washout Arms...
  • Page 15 Locate swashplate and slide it on the main shaft first. Install pivot balls as shown in the picture. Next locate the washout base, arms, links, M3x4 pivot studs, M3x10 cap head screws, M3x5x1 spacers, M3 set screws, and washout link pins. First slide an M3x10 cap head screw through each arm.

  • Page 16: Section 5 - Head Assembly

    Section 5 – Head Assembly Gather all the components for the head assembly. Install (1) Seasaw using (2) M3-8 Cap Head Bolts and (2) Seasaw Collars. Replacement Part Seasaw w/Brgs – QH357 Seasaw Collars – QHL355 Refer to the exploded view for further detail.

  • Page 17: Section 6 - Tail Assembly

    Section 6 – Tail Assembly Parts List Tail boom M3x4 Pivot Stud Belt 2.3 Medium ball ends Boom holder half x 2 Tail Pitch Lever M3x35 x 4 M3x4 Pivot stud M3 Locknut x 4 M3x10 Cap head screw Tail output shaft M3x3 Set screw Pulley gear Tail rotor hub...
  • Page 18 Locate the tail boom and the belt. Slide the belt through the boom. Be sure you do not twist the belt. Install the two boom halves into the frames. Put the (4) M3x35 cap head screws through the four open holes in the boom halves.
  • Page 19 Attach the side plate to the boom using two M3x6 cap head screws. Next slide your tail output and shaft through the side plate. Attach the other tail case side plate to the tail boom using (2) M3x6 cap head screws. Also attach the tail case cross member using (2) M3x6 cap head screws.
  • Page 20 Attach the tail pitch lever to the tail pitch lever base using an M3x10 cap head screw. Be sure that you capture the M3x4 pivot stud in the tail pitch slider with the brass coupler in the tail pitch lever. Attach the tail rotor ass’y to the tail output shaft using an M3x3 set screw.

  • Page 21: Section 7 - Linkage Rod Installation

    Section 6 – Fin Set Installation Parts List Vertical Fin Horizontal Fin C-clamp x 2 M3x14 Cap head screw x 4 Attach the horizontal fin using one black c-clamp and (2) M3x10 cap head screws. Note: Be sure the fin doesn’t interfere with the tail blades when they are rotating.
  • Page 22 In the following table the linkages will be measured center to center as per the picture. The table explains the amount of rods you need to make and which ball links to use on each end. This will get the helicopter close to finished setup, as always you will need to make some final adjustments to maximize the performance of your...
  • Page 23 All three swashplate rods will be the same length. # of Rods Rod Size 2.3-35 Ball Link 1 Medium Ball Link 2 Medium Center to Center 55mm Washout to Flybar Control Rod Use # of Rods Rod Size 2.3-20 Ball Link 1 Medium Ball Link 2 Medium...
  • Page 24 Seesaw to Hiller Arm Use a double link on this spot. Assemble the push rod guides. There are two pieces the main clip and two inner sleeves. Simply slide the sleeve into the main clip and glue. Putting electrical tape onto the boom before gluing is good, so it is possible to reuse the clip later.

  • Page 25: Section 8 - Motor Installation

    Swashplate to Rod Use Hiller arm # of Rods Rod Size 2.3-50 Ball Link 1 Long Ball Link 2 Long Center to Center 85mm Place the canopy where you like, mark the holes for the canopy standoffs. Use a ¼” drill bit.
  • Page 26 Attach your pinion gear to the motor using an M3x5 set screw. It is recommended to grind a flat onto the output shaft of the motor if there is not already one there. This will help to prevent the gear from slipping.
  • Page 27 Instead of giving you the exact length of each linkage rod we will explain to you what you are trying to achieve. This is the same for all Quick helicopters. Another thing worth mentioning is that all controls on our helicopters are leading edge controlled. We have three such controls on our helicopter and they are, Main blades, Tail blade and flybar control arms.
  • Page 28 position (horizontal on non push pull helis). Step 3 Connecting the Washout assembly. Connect the fixed length plastic “A” arms to the Swashplate, connect to the two longer pivot studs, if all four are the same length then any two will do. The next step is to adjust the length of the linkage rod between the Washout Arm and the Flybar connection point.
  • Page 29 Picture 3, Swash Up Picture 4, Head...
  • Page 30 Picture 5, Tail Center Picture 6, Tail Positive Thrust...
  • Page 31 Picture 7, Tail Negative Thrust Picture 8, Tail...
  • Page 32 Pitch Travel Setup Collective Position Normal Flying Aerobatic Up (100%) +10 deg +10 deg Center (50%) +5 deg +0 deg Down (0%) -3 deg -10 deg Throttle Curve Setup Electric Fuel (non governor mode) Collective Position Normal Normal Aerobatic Aerobatic Flying Flying Up (100%)
  • Page 33 Tail First adjust the servo arm position like you did with the swash, make sure your trim and sub-trim values are centered. Attach the servo arm so it's 90deg to the tail pushrod (vertical). Now adjust your two plastic ball ends, for the push rod, so they are screwed on about half way onto the threaded pushrod guide end piece.

Table of Contents