Quick Quickie.15 Manual
  1. Manuals
  2. Brands
  3. Quick Manuals
  4. Toy
  5. Quickie.15
  6. Manual
Quick Quickie.15 Manual

Quick Quickie.15 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
QuickWorldwide.com
Exclusively distributed by:
Quick worldwide
201 South 3
. St. & 309 N.
rd
Coopersburg, PA 18036
Phone: (610)-282-4811
Fax: (610)-282-4816
Quickie .15 Helicopters
Websites:
http://www.hhiheli.com
http://www.quickheli.com
http://www.giantscaleplanes.com
E-mail:
hhi@fast.net
Jon@ewtech.com
Support)
(Tech.

Advertisement

Table of Contents
loading

Related Manuals for Quick Quickie.15

Summary of Contents for Quick Quickie.15

  • Page 1 QuickWorldwide.com Quickie .15 Helicopters Exclusively distributed by: Websites: Quick worldwide http://www.hhiheli.com 201 South 3 . St. & 309 N. http://www.quickheli.com Coopersburg, PA 18036 http://www.giantscaleplanes.com E-mail: hhi@fast.net Phone: (610)-282-4811 Jon@ewtech.com (Tech. Fax: (610)-282-4816 Support)

  • Page 2: Pre-Assembly Information

    Quick Pre-Assembly Information Quick Worldwide & Hobbies & Helis International: Quick of Japan and Hobbies & Helis International teamed up to make parts 6 years ago. In the beginning, our specialty was the manufacturing of various upgrade parts for many of the plastic helicopters on the market.
  • Page 3 8. Control Linkages: The control linkages that are provided with the Quick Learner Kit are high quality 2.3mm stainless steel rods and the rod ends are made of a high quality Delrin. 9. Single Blade Axle Design: The single blade axle design is simple very responsive system, with very consistent flight characteristics.
  • Page 4 Tools Needed to Assemble the “Quick Learner” Ball End Drivers Phillips Screw Driver Bubble Blade Balancer HHI7050 HHI7010 High Point Balancer DUB499 Pitch Gauge HHI7001 HHI7320 – 6pc Nut & Piston Head Lock Allen Driver Set HHI7020 Composite Paddle Universal FlybarLock...

  • Page 5: Hardware And Accessories

    Hardware & Accessories Engines (These are our Recommended Motor but others will work) OS.15 CV-A Glues & Thread Lockers JB Weld…JBW8265S Locktite. …….PT40 Ca Glue. …GBG1 Exhaust Systems HHI 30 Size Long Tuned Pipe HHI 30 Size Tuned Muffler Tuned Pipe Accessories HHI 30/46 Size Tuned Heli-Pipe Rear Facing Exhaust Header Exhaust Coupler...
  • Page 6 Fuel System Accessories Tube Ends…. QUI9001 Fuel Filter… QUI9002 Mini Cock Straight… TET4321 Fuel Tubing…. PRA7092 Triangle Joint. …. TET4301 Radio Mounting Accessories Single Sided Foam Tape… HHI2008 Receiver Hold Down Straps HHI55** $4.99 2 Per Bag & Colors: Red, White, Purple, Black Receiver Strong Box…...

  • Page 7: Other Optional Accessories

    Other Optional Accessories Landing Gear Dampeners…HHI2004 3mm Fly-bar Stiffeners…HHI402* 60Size Skid Stops Quick Learner Servo Arm Set HHI200* Available in many Colors See website or Call for Detail 3mm Finishing Caps HHIM1110 Available in Blue, Silver, Gold, & Purple Base Load Antenna...
  • Page 8 Radio Requirements Radios: Hobbies & Helis & its distributors carry various lines of helicopter radios. Any radio that supports EMS/CCPM Mixing will work fine. We recommend using an eight-channel or better radio, although a six channel radio is all that is required. Servos: This is the single most important function of the helicopter.

  • Page 9: Section 1 - Upper Frame Assembly

    Section 1 – Upper Frame Assembly Parts List Bag 1 Frame Set Bag Main-shaft Bearing Block X 2 Main Frames X 2 M3x10 Self Tapping Screws x 16 M3x6 x 12 Radio Tray x 1 Lower Frame x 1 Rubber U-Channel x 2 Fuel Tank x 1 32mm Canopy Standoffs x 4 24mm Cross members x 2...
  • Page 10 Install four canopy standoffs (32mm) onto the two frame halves. Slide two frame halves over fuel tank with canopy mounts facing outward. The fuel tank is on the front of the helicopter, so looking from behind the helicopter the open hole on the tank goes out to the left.
  • Page 11 Install the lower frame stiffener using (8) M3x10 Self tapping screws. Install the front radio tray using (4) M3x10 self tapping screws. Install (1) 24mm cross member using (2) M3x6 cap head screws. Install (1) 24mm cross member using (2) M3x6 cap head screws.

  • Page 12: Section 2 -Landing Gear Installation

    Install the anti-rotation guide using (4) M3x10 self tapping screws. Install two boom halves using (4) M3x35 cap head screws, and (4) M3 locknuts. Section 2 –Landing Gear Installation Parts List Bag 2 Landing Gear Struts X 2 Landing Gear Skids X 2 Landing Gear Skid Ends X 4 M3x3 Set Screws x 4 M3x14 cap head screws x 4...
  • Page 13 Locate (2) Landing Gear Struts place a piece of masking tape across top and Center helicopter on the struts and mark holes Replacement Part #: Landing Gear Set – HHI4007 Drill (4) M3 holes at the previously determined locations. After holes have been Drilled remove tape.
  • Page 14 Install (2) Skid Pipes into the struts so the Helicopter is adequately balanced and secure using (4) M3 Set Screws. Install (4) Skid pipe end caps using medium CA glue. Bag 3 – Clutch bell Assembly, Counter Gear Assembly, and Main Gear Assembly. Clutch Bell M3 Locknut x 1 Clutch Lining...
  • Page 15 Score the clutch bell as shown. This provides better adhesion from the liner to the bell. Locate the lining and cut it to 98mm. Glue this in place with JB Weld. The best way we to hold the clutch liner to the bell is to wrap the clutch with a few rounds of electrical tape and slide that into the bell.
  • Page 16 Next, slide the start shaft bearing block onto the clutch bell and start shaft. Slide the start coupler over the top of the start shaft and secure it to the index mark. That means make sure the set screw hits the flat on the shaft.
  • Page 17 Slide the main sha ft through the two main shaft bearing blocks. The end with the hole closer to the end should go down through the blocks from the top side first. The main shaft will slide through the main gear assembly. Lock the bolt in place using a M3x18 and a M3 Locknut Next slide the main shaft collar...

  • Page 18: Parts List

    Secure the gear in place using the provided E-clip. Locate the two counter gear bearing blocks. Next slide each bearing block onto the counter gear shaft. Each bearing block has an open face. The open faces should in toward the gear. Then slide the pulley spacer on, and finally the cross locking pin.

  • Page 19: Section 5 - Clutch Assembly

    Install the fan shroud using (4) M3x10 self tapping screws. Section 5 – Clutch Assembly Parts List Fan Hub Motor Mount M3x10 x 4 M3x6 Flat head screws x 4 M2x8 x 1 Clutch Shim Ball x 1 M3x8 x 2 M3x6 Cap head screw x 4 Attach the fan to the fan hub using (4) M3x6 flat head screws.

  • Page 20: Section 6 - Control Items

    Attach the clutch to the fan hub using (2) M3x8 cap head screw. Attach the motor mount to the motor using (4) M3x10. Attach the shim ball to the throttle arm using a M2x8 screw. Slide the engine up into place and secure it using (4) M3x6 cap head screws.
  • Page 21 Antirotation guide pin M3x10 Cap head screws Washout link x 2 M3x5x1 Spacer x 2 Locate swashplate and slide it on the main shaft first. Next locate the washout base, arms, links, M3x6 pivot studs, M3x10 cap head screws, M3x5x1 spacers, and M2x12 pan head screws.

  • Page 22: Section 7 - Head Assembly

    Section 7 – Head Assembly Parts List Center Hub Hiller arm x 2 Seesaw M3x10 Cap head screw x 2 Seesaw Collar x 2 3x5x1 Spacer M3x8 Cap head screw x 2 Flybar M3x6 Pivot studs x 2 Flybar control arm base x 2 M3x16 Cap head bolt Flybar control arm extension x 2 M3 Locknut...
  • Page 23 Install two 7x13x3 o-rings into the head block. Next slide the head spindle through the o-rings. Then slide the head dampener spacers onto the spindle Each blade grip will have (2) 5x10x4R bearings. Install the bearings into the blade grip s. Slide each one onto the spindle shaft.
  • Page 24 Locate two 3x5x5 spacers, two flybar control arm bases, two flybar control arm extensions, and two M4x4 set screws. Slide (2) 3x5x5 spacers onto the flybar with the protruding side going against the seesaw. Next slide the flybar control arm bases onto the flybar.

  • Page 25: Section 8 - Tail Assembly

    Section 8 – Tail Assembly Parts List Tail boom M3x4 Pivot Stud Belt 2.3 Medium ball ends Boom holder half x 2 Tail Pitch Lever M3x35 x 4 M3x4 Pivot stud M3 Locknut x 4 M3x10 Cap head screw Tail output shaft M3x3 Set screw Pulley gear Tail rotor hub...
  • Page 26 Locate your tail output shaft and tail pulley gear. Secure the gear to the shaft using (2) M3x3 set screw. Locate your two tail case side plates. Install a 5x10x4R Bearing into each plate. Attach the tail pitch lever mount to the side plate using (2) M2x6 pan head screws.
  • Page 27 Slide the tail pitch slider assembly onto the tail output shaft. Attach the M3x4 pivot stud to the tail pitch lever. Attach the tail pitch lever to the tail pitch lever base using an M3x10 cap head screw. Be sure that you capture the M3x4 pivot stud in the tail pitch slider with the brass coupler in the tail pitch lever.
  • Page 28 Attach a tail blade to each grip using (2) tail blade spacers, an M3x20 cap head bolt, and an M3 locknut. Note: The Tail Blades should rotate counter clockwise when looking at the right side of the Tail Case. Section 9 – Fin Set Installation & Fuel Tank Assembly Parts List Vertical Fin Fuel tank outer plate...

  • Page 29: Section 10 - Linkage Rod Installation

    Attach the vertical fin using one c-clamp and (2) M3x14 cap head screws. Section 10 – Linkage Rod Installation Parts List M2x8 Pan head screws x 8 2.3mm Ball end, Long x 10 Shim ball x 8 Double Link x 2 M2.3x35mm Linkage Rod x 2 Canopy M2.3x50mm Linkage Rod x 4...
  • Page 30 Step 1 – Linkage Rod Setup In the following table the linkages will be measured center to center as per the picture. The table explains the amount of rods you need to make and which ball links to use on each end. This will get the helicopter close to finished setup, as always you will need to make some final adjustments to...
  • Page 31 Upper Swash Servo to Rod Use Swashplate # of Rods Rod Size 2.3-35 Ball Link 1 Medium Ball Link 2 Medium Center to Center 55mm Lower Swash Servo to Rod Use Swashplate # of Rods Rod Size 2.3-50 Ball Link 1 Long Ball Link 2 Long...
  • Page 32 Washout to Flybar Control Rod Use # of Rods Rod Size 2.3-20 Ball Link 1 Medium Ball Link 2 Medium Center to Center 38mm Seesaw to Hiller Arm Use a double link on this spot. Assemble the push rod guides. There are three pieces the main clip and two inner sleeves.
  • Page 33 Install the carbon rudder control rod. The rod should end up 22” or 558mm long from ball to ball. Slide the carbon rod through the guides and glue the ends on. Screw the links onto the ends and attach to the balls. Swashplate to Rod Use Hiller arm...
  • Page 34 Place the canopy where you like, mark the holes for the canopy standoffs. Use a ¼” drill bit. Place the grommets in the holes and secure the canopy to the helicopter using (4) M3x14 cap head screws. Radio Setup General Information: First, change your radio to 3 Point, 120 Degrees swash-plate mixing.
  • Page 35 Throttle Curve Setup: Normal Mode, Bottom-Stick 20 Percent throttle; Mid-Stick, 50 Percent Throttle, Top Stick 100 Percent Throttle. Stunt 1 & 2 Bottom-Stick 100 Percent; Mid-Stick, 35 Percent; Top Stick, 100 Percent. Tail Rotor: Setup the Tail rotor limits so the throws that the tail pitch slider does not exceed a 5mm gap between the tail case and the tail pitch slider.
  • Page 36 height, just lock the pin down. Engine Break-in: Be sure to break in the engine with a prop or loosen the glow plug so not to break to start shaft. The 15 CV-A and car engines have very tight compression.

Table of Contents