Westinghouse T28074 Quick Start Manual

3-Outlet Wireless Remote Control
Outdoor Wireless Remote Control
3 grounded outlets and plug
6in AWG 14/3 SJTW vinyl cord
Rated: 125VAC/60Hz/15A/1875W Resistive
8A/1000W Tungsten
Battery: 3 Volt CR2032 lithium battery (included)
INSTRUCTIONS:
Insert the Receiver Base's 3-prong plug into a grounded
outlet. If using outdoors, be sure to plug into a GFCI approved
outlet. Using the keyhole bracket, mount the Receiver Base
at least 6˝ from the ground to prevent exposure to water in
case of flooding. Plug your devices into the outlets located
on bottom of Receiver Base. Using the Wireless Transmitter,
press the ON button to activate device.
Manual Override: You can power the unit ON and OFF
manually by pressing the ON/OFF override button located on
the front of the Receiver. (Do not hold the button down for
manual ON/OFF operation as this will cause the unit to enter
pairing mode.)
PHOTOCELL MODE:
Photocell Mode turns OFF your device automatically at dawn
even when you forget.
1. Make sure the sliding mode switch on the transmitter is in
the Photocell position.
2. Press the ON button to turn the power on. All
connected devices will turn on instantly and will turn off
automatically at dawn.
3. To cancel Photocell Mode, slide the Photocell switch
into the manual position and press either the ON or OFF
button to initiate. (Note: Sliding the photocell switch
without pressing a corresponding function button (ON/
OFF) will not initiate or cancel the photocell function.
COMMAND1 TRANSMITTER PAIRING:
Note: Your Command1 Transmitter and Receiver contained
in this package are pre-programmed and ready to use.
Command1 Pairing is only required for using additional
transmitters.
This unit is equipped with patented Command1 technology.
All indoor and outdoor transmitters bearing the Command1
logo have the ability to be paired with all other Command 1
indoor and outdoor receivers. Please follow the directions
below to pair a transmitter to your receiver.
1. Locate the power button on the receiver.
2. Press and hold the power button for 3 seconds. The LED
power indicator beneath the button will begin to flash
slowly.
3. On your transmitter, (LED indicator still flashing slowly)
press the ON button, wait 2 seconds, and then press the
OFF button. The LED indicator will now stop flashing.
4. You have successfully paired the transmitter to your
receiver.
RESETTING THE UNIT
You can reset and remove all paired transmitters from your
receiver by doing the following:
1. Press and hold the POWER button for 3 seconds. The
LED indicator will begin to flash slowly. Continue to hold
for an additional 3 seconds. The LED indicator will now
begin to flash rapidly. Release the POWER button for 1
second and press once again to confirm reset. The LED
indicator should now be OFF.
2. Your unit has now been reset and does not have any
paired transmitters. (Note: After reset, pairing is required
to use the transmitter shipped in this package.)
SAVE THESE INSTRUCTIONS!
Customer Service Assistance: Toll Free 1-855-350-6868
Hours of Operation: 10AM to 6PM, EST, Monday - Friday
and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license. All rights reserved.
Manufactured and distributed by: The NCC, Brooklyn, NY 11220 • www.thencc.com • © 2014 The NCC
Transmitter
Receiver Base
BATTERY INFORMATION
AND REPLACEMENT:
The Transmitter uses a 3 volt CR2032 lithium battery. To
replace, slide open the battery tray on the bottom of the
transmitter. Insert a new CR2032 lithium battery, making
sure to match up the + and - polarity markings. To test, press
the ON or OFF buttons to make sure the LED lights up. Slide
the tray back in. Do not dispose of batteries in fire. Batteries
may explode or leak.
WARNING:
Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is needed.
• Consult the dealer or an experienced radio/TV technician
for help.
Problem
The receiver doesn't turn on
The transmitter doesn't work
CAUTION:
DO NOT splice, repair, or modify. Unplug when not in use.
Fully insert plug. DO NOT use damaged remote sets. Inspect
periodically. Use within the electrical rating marked on the
remote set. DO NOT plug in more than a total of 1875 watts
in this remote set. If watts are not marked on appliance,
multiply ampere rating (on nameplate) by 125 to determine
equivalent watts. Add determined watts for each plugged-in
appliance or lamp (sum of watts on bulbs) to find total watts
being used. Operating temperature range -22°F (-30°C) to
113°F (45°C).
• Only use the batteries specified and be sure to match the
+ and - polarity markings.
• Remove exhausted or dead batteries from the product.
• Remove batteries if product is not to be used for a long
time.
• Do not dispose of batteries in fire. Batteries may explode
or leak. As with all small items, these batteries should
be kept away from children. If swallowed, seek medical
attention immediately.
*This item is a Radio Frequency device (RF), and as such the
range of the remote control is dependent on many factors.
Actual operational distance will vary based on walls and line
of sight obstructions, and other nearby electronic devices.
THREE YEAR LIMITED WARRANTY:
If within the first year from date of purchase, this unit fails
due to a defect, exchange where purchased, or ship it prepaid
with proof of purchase to The NCC, 140 58th Street, P.O.
Box 67, Brooklyn, New York 11220. Units that fail to operate
during the second or third year from date of purchase must
be shipped prepaid with proof of purchase to The NCC.
We will replace unit. This guarantee excludes normal wear
and tear and damage resulting from accident, alteration, or
misuse. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
NOTE: If you are experiencing interference between 2
devices, please follow the instructions below:
CHANNEL SELECTOR:
The back of your transmitter is equipped with a channel
selector switch to prevent interference between devices
around your home. To prevent interruption between 2
devices, set your transmitter to an alternate channel.
Transmitter channel codes are as follows:
A, B, C, D.
Location: Peel off the sticker located below the word
"channel" on the back of the transmitter to expose the
channel selector switch.
Be aware that every time a channel is changed
Command1 Transmitter Pairing is required.
See Transmitter Pairing instructions.
Solution
Make sure the AC power cord is securely plugged into an AC power outlet.
Unplug the unit for a moment, and then plug it back in again.
Check the outlet by plugging in another device.
Make sure the battery is fresh.
Stand closer to the receiver. The range should be up to 80ft.
Doors or walls will reduce the effective range.
T28074
TC28074
Made in China