Advertisement
Method D - Automatic
code search
With this method, the remote control scrolls through the
full code list by sending an IR signal to the set to be
controlled remotely. Proceed as follows:
1. Check that your equipment is on. If not, switch it on
manually.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes to signal that this time is almost up,
and then goes off).
3. Release the SETUP key.
4. Press the PROG+ or standby B
seconds, the remote control begins to scroll through
the whole code list included in the library (at a rate
of roughly 1 code per second). Press the PROG+
key once again to slow down the test speed (1 code
every 3 seconds). As soon as the set changes
channels, you must press OK to save the code and
stop the remote control scrolling through the list. If
you do not react quickly enough, you can go back
to the previous code by pressing PROG- as many
times as necessary (you can go forward by
pressing B
B , PROG+ if you have gone back too
far). As soon as the set responds again, press OK
to save the code.
How to retrieve
a programmed code
It may be useful to retrieve the code programmed in the
remote control.
1. Hold down the SETUP key until the red indicator
light blinks and then remains lit.
2. Press the SETUP key again briefly, the indicator
light blinks once.
3. Press the number keys in decreasing order (9 to 0)
until you notice that the indicator lamp blinks once.
4. The number which made the indicator lamp blink is
the first of the four figures comprising your code,
write it down. Repeat to obtain the other two codes.
5. Repeat step 3 to find out the two other numbers of
the code.
6. When the fourth figure is found, the indicator lamp
goes out.
Check of
the programming
Turn on the set and press, for example, 2 to change
channels.
Try other remote control keys to find out the range of
functions you can control. If you think that not all of the
keys are active, try the programming Method B or C.
When you have retrieved the code of your
set, jot it down so that you can use it
whenever needed.
After battery replacement, you'll have to
programme the remote control again.
TV CODE
The THOMSON NAVILIGHT system allows you easy
access to the settings of your television (TV) including this
feature.
1. Switch on the set you want to control.
2. Press key MENU once.
3. Navigate through the setting menus with the keys up,
4. Validate with OK.
5. To leave the menus, press key EXIT once.
B key. After a few
recycling system for which producers are responsible
• This appliance has been designed and manufactured
with high quality materials and components that can be
recycled and reused • Electrical and electronic
appliances are liable to contain parts that are
necessary in order for the system to work properly but
which can become a health and environmental hazard
if they are not handled or disposed of in the proper
way • Consequently, please do not throw out your
inoperative appliance with the household waste • If you
are the owner of the appliance, you must deposit it at
the appropriate local collection point or leave it with the
vendor when buying a new appliance • If you are a
professional user, please follow your supplier's
instructions • If the appliance is rented to you or left in
your care, please contact your service provider • Help
us protect the environment in which we live !
2
The NAVILIGHT system
down, left, right ( ,
This symbol means that your inoperative
electronic appliance must be collected
separately and not mixed with the
household waste • The European Union
has implemented a specific collection and
You can contact THOMSON by dialling:
0871 500 0520
(call to this number
will be charged at 10 pence per minute)
http://www.thomsonlink.com
ROC1407 / GB - bj - XX / aws - rst / 01-2007
,
,
).
Advertisement
