Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for STI FINO
Summary of Contents for STI FINO
- Page 1 Assembly Instructions Solar collector FINO...
-
Page 2: Table Of Contents
STI GmbH. The instruction can only be duplicated completely or in parts with written authorisation of the STI GmbH. Subject to technical changes and misprints. The STI GmbH is obliged to take back with the environmental label RAL-UZ-73 for solar collectors ( „Blauer Engel“) labeled products, and to consign it to recycling. -
Page 3: Safety Regulations, Instructions And Guidelines
Safety regulations, instructions and guidelines Engineer standards and guidelines • VBG 4 Unfallverhütungsvorschriften Elektrische Teil 2: Sonnenheizungsanlagen mit organischen Anlagen und Betriebsmittel Wärmeträgern; • VBG 37 Unfallverhütungsvorschrift Bauarbeiten Anforderungen an die sicherheitstechnische Ausrüstung • VBG 74 Leitern und Tritte • DIN VDE 0100-510 Errichten von Starkstromanlagen mit •... - Page 4 Safety regulations, instructions and guidelines Statics The selected substructure and the connections to the building are to be interpreted by others according to local Before beginning the assembly it is vital to test the roof or circumstances. substructure on site to sufficient load-carrying capacity. Recommended heat transfer medium is Tyfocor LS or Pay increased attention to the possible durability of the equivalent.
-
Page 5: Product Descriptions
Product descriptions Solar thermal collector „FINO“ The solar collector uses the radiant energy of the sun for heating a heat transfer fluid. This glycol-water mixture indicates the stored heat through a heat exchanger to a storage tank. The energy can be used for hot water installation. - Page 6 (see figure) These are available as a kit from your supplier. The collector can be mounted onto slanted roofs or console constructions (flat roofs, base or b arri- er). Specifications Model FINO cross area 0,96 m² length 1.200 mm width...
- Page 7 Product description Hydraulic connections The hydraulic connection between the collectors requires standard clamping ring joints (10 mm). Example: Supplier: Simplex VSH SUPER Please note the assembly instructions of your supplier. The maximum allowable operating pressure is 6 bar. Pressure drop per collector at design conditions (Tm = 20°C und dV/dt = 50 l/h) Δp = 2930 Pa Table of measurements (Pa) (Tm = 20 °C)
-
Page 8: Collector Hydraulic
Collector hydraulic Arrangement options Each collector has unilaterally a flow and return connection (tube 10 mm.) up to four collectors can be connected in series. In parallel interconnecting any number of such fields can be combined, taking into account the pressure losses. The dimension of the connecting pipe is always 10x1 mm (A) between two collectors. - Page 9 Collector hydraulic in three rows with three collectors in two rows with two collectors in three rows with six collectors in two rows with four collectors...
- Page 10 Collector hydraulic in four rows with eight collectors...
-
Page 11: Assembly
The distances between the collectors can be chosen depending on the arrangement of the collectors. The solar collector FINO provides air inlets at the right and left site which are covered with a grommet. It is mandatory that the opening of the grommet is adjusted parallel to the floor. - Page 12 Assembly Installation of substructure It is recommended to mount the FINO on an outsite sub construction (aluminium profile, console, etc.), which is not scope of delifery. Before starting to mount the collector it is mandatory, to check the roof and the onsite sub construction regarding load capacity and taking into account wind and snowloads.
-
Page 13: Pipe Dimension
Pipe dimension Recommended pipe dimension for connections length of pipe FL+RE up to from from from from from 5 m up 10 m up 15 m up 20 m up 25 m up to 10 m to 15 m to 20 m to 25 m to 30 m number of collectors... -
Page 14: Initiation
Initiation Initial operation Regular inspections After installing the other components such as flow pipe, Solar systems should be reviewed at intervals to be determined in return pipe, insulation, pump group, expansion tank and addition to the function control by the operator. controller the installation can be put into service. -
Page 15: Appendix
Appendix... - Page 16 STI Solar Technologie International GmbH Seiferitzer Allee 14 08393 Meerane GERMANY Tel: + 49 03764 795610 Fax: + 49 03764 7956115 E-Mail: info@sti-solar.de Homepage: www.sti-solar.de Version 10/2012 © Copyright 2015...
Need help?
Do you have a question about the FINO and is the answer not in the manual?
Questions and answers