Advertisement
"b" is Control Change and "x" is a hexadecimal
value for the MIDI channel 0-F (1-16).
Assigning the on-board pedal - Footswitch 1
•
Press [FC EDIT], to select Foot Control Edit.
Press footswitch button, 1 to select Foot
Controller 1 to be edited (the lamp above the
footswitch will flash).
•
STATUS will be flashing. Press [INC/YES] or
[DEC/NO] as necessary to select b0. The
letter "b" indicates this will be a Control
Change command. This will set the FC7 for
the
on-board
FC
information on MIDI Channel 1 (the zero
indicates MIDI channel 1).
•
Press [FC EDIT] to set the DATA/CTRL and
use [INC/YES] and [DEC/NO] to select 007.
This selects the Volume, Controller #7.
•
Press [FC EDIT] to see Maximum Volume 127
•
Press [FC EDIT] to see Minimum Volume 000
•
Push the [Write/Exit] Switch, FC1 will flash in
the screen and then push [INC/YES]. This has
stored the information.
Assigning an FC7 – use Footswitch 2 to make the
assignment
•
Press [FC EDIT], to select Foot Control Edit.
Press footswitch button, 2 to select Foot
Controller 2 to be edited (the lamp above the
footswitch will flash).
•
Press [FC EDIT] again to select STATUS. Press
[INC/YES] or [DEC/NO] as necessary to select
b1. The letter "b" indicates this will be a
Control Change command. This will set the
FC7 for the on board FC to transmit controller
information on MIDI Channel 1 (the "1"
indicates MIDI channel 2).
•
Press [FC EDIT] to set the DATA/CTRL and
use [INC/YES] and [DEC/NO] to select 007.
This selects the Volume, Controller #7.
•
Press [FC EDIT] to see Maximum Volume 127
•
Press [FC EDIT] to see Minimum Volume 000
•
Push the [Write/Exit] Switch, FC2 will flash in
the screen and then push [INC/YES]. This has
stored the information.
Assigning an FC7 - Footswitch 3 to make the
assignment
•
Press [FC EDIT], to select Foot Control Edit.
Press footswitch button, 3 to select Foot
Controller 3 to be edited (the lamp above the
footswitch will flash).
•
Press [FC EDIT] again to select STATUS. Press
[INC/YES] or [DEC/NO] as necessary to select
b2. The letter "b" indicates this will be a
Control Change command. This will set the
FC7 for the on board FC to transmit controller
information on MIDI Channel 3 (the "2"
indicates MIDI channel 3).
to
transmit
controller
•
Press [FC EDIT] to set the DATA/CTRL and
use [INC/YES] and [DEC/NO] to select 007.
This selects the Volume, Controller #7.
•
Press [FC EDIT] to see Maximum Volume 127
•
Press [FC EDIT] to see Minimum Volume 000
•
Push the [Write/Exit] Switch, FC3 will flash in
the screen and then push [INC/YES]. This has
stored the information.
Assigning an FC7 - Footswitch 4 to make the
assignment
•
Press [FC EDIT], to select Foot Control Edit.
Press footswitch button, 4 to select Foot
Controller 4 to be edited (the lamp above the
footswitch will flash).
•
Press [FC EDIT] again to select STATUS. Press
[INC/YES] or [DEC/NO] as necessary to select
b3. The letter "b" indicates this will be a
Control Change command. This will set the
FC7 for the on board FC to transmit controller
information on MIDI Channel 4 (the "3"
indicates MIDI channel 4).
•
Press [FC EDIT] to set the DATA/CTRL and
use [INC/YES] and [DEC/NO] to select 007.
This selects the Volume, Controller #7.
•
Press [FC EDIT] to see Maximum Volume 127
•
Press [FC EDIT] to see Minimum Volume 000
•
Push the [Write/Exit] Switch, FC4 will flash in
the screen and then push [INC/YES]. This has
stored the information.
Now each Pedal will control a separate MIDI
channel of your MIX 1-4.
Assigning Pitch Control to a Foot Controller
Bending Up (toe down = pitch up)
•
Press the [FC EDIT] button
•
Press Footswitch 1 to set the on-board FC
•
STATUS = E0 Pitch Bend on MIDI channel 1
•
Press [FC EDIT]
•
DATA/CTRL = ---
•
Press [FC EDIT]
•
Set Maximum to 127
•
Press [FC EDIT]
•
Set Minimum to 64
•
Push the [Write/Exit], then [INC/YES]
Bending Down (heel down = pitch down)
•
Press the [FC EDIT] button
•
Press Footswitch 1 to set the on-board FC
•
STATUS = E0 Pitch Bend on MIDI channel 1
•
Press [FC EDIT]
•
DATA/CTRL = ---
•
Press [FC EDIT]
•
Set Maximum to 64
•
Press [FC EDIT]
•
Set Minimum to 0
•
Push the [Write/Exit], then [INC/YES]
Assigning Aftertouch to a Foot Controller
•
Press the [FC EDIT] button
•
Press Footswitch 1 to set the on-board FC
7
Advertisement
