Related Manuals for Konig VID-TRANS300
Summary of Contents for Konig VID-TRANS300
- Page 1 VID-TRANS300 VID-TRANS310 VID-TRANS320 & CIRCUIT TILT NIGHT VISION BUILT-IN IR LED OBSERVATION & SECURITY CHANNELS UNIT MANUAL ENGLISH...
- Page 2 Systems: VID-TRANS300 1x Pan/Tilt Camera 1x 2.5” LCD/TFT monitor 2x AC/DC adapter 1x Audio/Video cable 1x In-ear headphone Batteries not included VID-TRANS310 1x Pan/Tilt camera 1x Receiver with antenna 1x Remote control 2x AC/DC adapter 1x Audio/Video cable Batteries not included...
- Page 3 Description receiver VID-TRANS300: Channel indicator: indicates which channel is in use LCD screen: displays the picture of the camera Camera manual vertical rotation: rotates the camera in vertical direction (cursor up = camera up, cursor down = camera down) Camera power button: switches the camera on or off...
- Page 4 Operation receiver VID-TRANS300: 1) Put the camera in position 2) Connect the AC/DC adapter to the camera. Switch on the camera with the power switch. The power indicator lights up. Select a channel. 3) Connect the AC/DC adapter to the receiver or place 4x AAA batteries into the battery compartment for power.
- Page 5 For the description and operation of the camera see chapter : “description camera” Description receiver VID-TRANS310 Mute Button Antenna: omni-directional antenna for receiving of 2.4GHz signal Channel indicator: indicates which channel is in use Channel button: select channel 1, 2 or 3 (note: select the same channel as chosen on the camera) Mode control: setting for channel set-up AV output: connection to TV/monitor or recorder with audio/video cable...
- Page 6 6) The TV/monitor shows the picture of the camera. Channel set-up receiver VID-TRANS300: The receiver supports up to 3 cameras working at the same time. All cameras can be seen in sequel. See mode control at the backside of the camera for settings.
- Page 7 Description camera VID-TRANS320 (VID-TRANS300, 310): Microphone Rotate axis: rotating part of the camera, controlled by remote control Infrared lights: 10 IR LED’s for night view Lens: adjustable (focus) lens with CMOS image chip Microphone: built-in microphone for sound monitoring Base: stand/holder for the Pan & Tilt camera Antenna: omni-directional antenna for sending of 2.4GHz signal...
- Page 8 Operation with VID-TRANS300: Use the cursor buttons on the LCD monitor of the receiver to rotate the Pan & Tilt camera. When using up to 3 cameras, select for every camera a different channel. The Pan & Tilt function is available for the channel which is chosen on the receiver.
- Page 9 Operation remote control: 1) Press the power button on the remote control to switch on the camera (Press again to switch off the camera when not in use). 2) Press the channel button on the remote controller to select the channel.
- Page 10 Designs and specifications are subject to change without notice. Specifications: Receiver VID-TRANS300 Power Supply: 8 VDC Controls: Brightness, volume, camera on/off Display: 6,5cm Consumption Current (Max.): 250mA Receiving Frequency: 2,400GHz~2,483GHz Modulation: FM Receiving Sensitivity: <= -85 dBm Video Output Signal Impedance: 75 ohm Video Output Signal Level: 1.0 V +/- 0.15 Vpp...
- Page 11 Dimensions: 42 x 19 x 85 mm (Excluding Antenna) Camera VID-TRANS320 (VID-TRANS300, 310) Imaging Sensor: CMOS Pixels: 628x582 (PAL) Horizontal Resolution: 380 TV Lines View Angle: 60 Degree Minimum Illumination: 0 Lux Transmission Frequency: 2,400~2,483 GHz Transmission Power: 10mW Modulation: FM...