Use extreme caution when installing or removing components. Refer to the installation instructions in this user’s guide for precautions and procedures. If you have any questions, please contact Quanmax Post-Sales Technical Support. WARNING High voltages are present inside the chassis when the unit’s power cord is plugged into an electrical outlet.
Static electricity can harm system boards. Perform service at an ESD workstation and follow proper ESD procedure to reduce the risk of damage to components. Quanmax strongly encourages you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment.
Page 8
Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. Do not handle or store system boards near strong electrostatic, electromagnetic, magnetic, or radioactive fields. QDS-8200 User’s Manual...
Remove all items from the box. If any items listed on the purchase order are missing, notify Quanmax customer service immediately. Inspect the product for damage. If there is damage, notify Quanmax customer service immediately. Refer to “Warranty Policy” for the return procedure.
Quanmax or its authorized agent; or if the failure is caused by accident, acts of God, or other causes beyond the control of Quanmax or the manufacturer. Neglect, misuse, and abuse shall include any installation, operation, or maintenance of the product other than in accordance with the user’s guide.
Quanmax. Limitation of Liability In no event shall Quanmax be liable for any defect in hardware, software, loss, or inadequacy of data of any kind, or for any direct, indirect, incidental, or consequential damages in connection with or arising out of the performance or use of any product furnished hereunder.
Page 12
Line conditioners keep a system’s AC power source voltage at a fairly constant level and, therefore, can handle brownouts. Because of this added protection, line conditioners cost more than surge protectors. However, line conditioners cannot protect against a complete loss of power. QDS-8200 User’s Manual...
Page 13
Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety approved. QDS-8200 User’s Manual...
Chapter 1 Introduction Overview Powered by ARM® Cortex®-A17 processor, QDS-8200 is a highly integrated mini PC board designed for TV / monitor / digital signage / IPC and surveillance industries. Providing the benefit for lowering cost and reducing design effort perspective, it definitely is your best option in solution survey.
No.1. To move a jumper from one position to another, use needle-nose pliers or tweezers to pull the pin cap off the pins and move it to the desired position. QDS-8200 User’s Manual...
Chapter 2 Jumper Settings and Pin Definitions For jumper and connector locations, please refer to the diagrams below. Figure 3 Jumper and Connector Locations QDS-8200 User’s Manual...
For jumper descriptions, please refer to the table below Table 2 Jumper List Item Function LVDS Panel Power Selection Table 3 #1 LVDS Panel Power Selection Jumper Status 1-2 Short 3.3V 3-4 Short 5-6 Short QDS-8200 User’s Manual...
USB Host Pin Header USB Host Pin Header OTG Control Pin Header HDMI In Connector AD Key Output Wafer IR Wafer (optional) V-By-One Connector (optional) Table 5 #2 Backlight Power Output Wafer Signal Name LCD-BLON LCD-ADJ Pitch: 2.0 mm QDS-8200 User’s Manual...
Table 9 #6 Microphone Input Wafer Signal Name MIC+ MIC- Pitch: 2.0 mm Table 10 #7 UART4 / RS232 Wafer* Signal Name 3.3V / 5V* Pitch: 2.0 mm * default 3.3V for UART; optional 5V for RS232 QDS-8200 User’s Manual...
Table 13 #10 UART1 Wafer Signal Name 3.3V Pitch: 2.0 mm Table 14 #11 Touch Panel Wafer Signal Name 3.3V Pitch: 2.0 mm Table 15 #12 GPIO Wafer Signal Name GPIO7_B7 GPIO7_B6 GPIO7_B5 GPIO7_B4 GPIO7_B2 Pitch: 2.0 mm QDS-8200 User’s Manual...
Table 17 #14 AD Key Input Wafer Signal Name ADKEY POWERON Pitch: 2.0 mm Table 18 #15 / #16 / #17 USB Host Wafer Signal Name Pitch: 2.0 mm Table 19 #18 OTG Control Pin Header Signal Name Pitch: 2.0 mm QDS-8200 User’s Manual...
Signal Name CLKN CLKP STBY HPDOUT RCLK_RX SCLK SDA3 SCL3 Pitch: 2.0 mm Table 21 #20 AD Key Output Wafer Signal Name Pitch: 2.0 mm Table 22 #21 IR Wafer (optional) Signal Name IR-INT 3.3V Pitch: 2.0 mm QDS-8200 User’s Manual...
GbE LAN RJ-45 Connector Line-out Audio Jack USB2.0 Type-A Connector USB OTG Micro-USB Connector Micro SD Cage Front Panel Connectors Figure 5 Front Panel I/Os Table 25 Rear Panel Connector List Item Function ADB Button Power LED QDS-8200 User’s Manual...