1. Manuals
  2. Brands
  3. Projecta Manuals
  4. Control Systems
  5. INTELLI-RV PM100
  6. Instruction manual

Projecta INTELLI-RV PM100 Instruction Manual

12v power management system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INTELLI-RV
12V POWER MANAGEMENT SYSTEM
IMAGE TO BE UPDATED
P/No. PM100

Advertisement

Table of Contents
loading

Summary of Contents for Projecta INTELLI-RV PM100

  • Page 1 INTELLI-RV 12V POWER MANAGEMENT SYSTEM IMAGE TO BE UPDATED P/No. PM100...

  • Page 2: Table Of Contents

    CONTENTS 1. SYSTEM INTRODUCTION PM100.........3 1.1 Features 1.2 Battery Charger of stationery/service battery 1.3 Battery Low Voltage Protection 1.4 Voltage Charging Relay (VCR) 1.5 Specification 2. STRUCTURE..............8 3. OPERATION..............9 3.1 Configuration 3.2 Wiring 3.3 LED display 4. DISPLAY EXPLANATION AND TROUBLESHOOTING ...11...

  • Page 3: System Introduction Pm100

    1. System Introduction PM100 PM100 is designed for use in caravans or motor homes. The PM100 is designed for an easy installation and a user-friendly interface without the need for a highly tailored cable harness. IMAGE TO BE UPDATED PM100 unit 1.1 Features Smart battery charger 12V 35A (20A for Charging Current) - Multiple battery charging stages to ensure the proper charging to battery...
  • Page 4 WORKING PRINCIPLE AC/DC AC IN Shunt Shunt BLVP Load+ Load- BAT+ BAT- SBAT- SBAT+ 15A DC- 10A DC- 15A DC+ 10A DC+ Load Caravan LOAD1~LOAD4 LOAD5~LOAD10 LOAD1~LOAD4 LOAD5~LOAD10 Battery Battery 15A*4 10A*6 15A*4 10A*6 MULTIPLE INPUTS PM100 has two inputs: AC mains and auxiliary (AUX). There will only be one source providing power at a time, even if all are available, priorities are listed below.

  • Page 5: Battery Charger Of Stationery/Service Battery

    1.2 Battery Charger of stationery/service battery The charger automatically starts when the power is connected, either from grid or generator. With multiple charging stages (soft start, bulk, absorption, float, recycle), PM100 is designed to fully charge the battery quickly. To guarantee the optimal charging for batteries of different states, the PM100 features a Microprocessor-controlled charging algorithm.

  • Page 6: Voltage Charging Relay (Vcr)

    1.4 Voltage Charging Relay (VCR, also known as a VSR) PM100 has a built-in voltage charging relay (VCR), which offers a convenient source to charge the service battery by alternator whilst engine is running. When the starter battery reaches 13.4VDC with threshold time delay, the VCR will charge the service battery from the alternator.
  • Page 7 Model PM100 OTHERS Disconnect voltage 10.5VDC Battery Disconnect Delay off time 60Sec (LVD) Reconnect voltage 11.5VDC 200mA 240VAC is off, no vehicle charging LVD battery <10.5V. 60mA Current draw on battery Current draw on battery LVD battery <10.0V. Current draw on battery Numbers Fused outputs Rated current...

  • Page 8: Structure

    2. Structure 38,5 Ø5 196,9 11,5 11,5 12,5 Hole size...

  • Page 9: Operation

    3. Operation 3.1 Configuration 146,9 SIDE PANEL 4 5 6 7 8 9 Label Definition Description POWER AC input port OFF/Charger Mode selection switch Power supply or charger mode Power supply Load Switch Load switch connector Connect external switch Starter Bat+ Connect to starter battery+ Starter battery connector Connect to starter battery-...

  • Page 10: Led Display

    3.3 LED display color Status Description AC input ok Mains Green AC disconnected VCR connected Slow flashing The voltage of starter battery is normal but the service battery is charged by the AC （flash once every second） Starter Green Bat. Quick flashing The voltage of starter battery doesn't meet the requirements, （flash twice every second）...

  • Page 11: Display Explanation And Troubleshooting

    4. Display explanation and Troubleshooting Illuminating Flash * When the PM100 detects the voltage of the starter battery is below 2V, it assumes that starter battery is not connected to our system. Mains Str Bat. Charge Fault Description Solutions Power supply mode (PS mode) AC grid is working as the source of power supply.
  • Page 12 “Charge”flashes as 1 sec on then 2 sec off If the fault still exists, please contact the PM100 unit over temp alarm. distributor, installer or PROJECTA PM100 is working under CHG mode. 1. Check the setting of the battery capacity.
  • Page 13 NOTES...
  • Page 14 WARRANTY STATEMENT Applicable only to product sold in Australia Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxfield, Vic.,telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue (save and except for all bulbs and lenses whether made of glass or some other substance) will under normal use and service be free of failures in material and workmanship for a period of one (1) year (unless this period has been extended as indicated elsewhere) from the date of the original purchase by the consumer as marked on the invoice.

Table of Contents