Download Print this page
Allen-Bradley 140MG-H Adjustment Instruction

Allen-Bradley 140MG-H Adjustment Instruction

Advertisement

Quick Links

DIR 1000721R0507 Version 04 - 140MG-H8E_, 140MG-J8E_
Adjustment Instruction for 140MG-H, 140MG-J
Settaggio sganciatori
Auslöser
Dèclencheur
Relé
* fold this paper with barcode on the outer side
1000721R0507
Installation - Installazione - Instalación
Instalação -
WARNING:
To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
Vor Installations- oder Servicearbeiten Stromversorgung zur
WARNUNG:
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT:
Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。
DIR 1000721R0507 Version 04
-
140MG-H
CLACK
1
Bul. 140MG
140MG-J
1
1
2
1

Advertisement

loading

Summary of Contents for Allen-Bradley 140MG-H

  • Page 1 Bul. 140MG DIR 1000721R0507 Version 04 - 140MG-H8E_, 140MG-J8E_ Adjustment Instruction for 140MG-H, 140MG-J Settaggio sganciatori Auslöser Dèclencheur Relé * fold this paper with barcode on the outer side 1000721R0507 Installation - Installazione - Instalación Instalação - WARNING: To prevent electrical shock, disconnect from power source before installing or servicing.
  • Page 2 Color CONDITION Run time Green LED Fully illuminated = L pre alarm (0.9 I1 < I < 1.2 I1) LED Flashing = Overcurrent fault (I > 1.2 I1) LED Flashing = Phase Unbalance L | U | I LED Flashing = Trip Coil disconnected 140G-ELTT is required for fault identification in compliance with UL508A Default setting Settaggio di default...
  • Page 3 140G-ELTT (Ordered separately) Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page...

This manual is also suitable for:

140mg-j