Table of Contents
Advertisement
• To join the equipment to the mains supply, use the power cord purchased with the
• To join the equipment to the mains supply, use the power cord purchased with the
• To join the equipment to the mains supply, use the power cord purchased with the
equipment.
• The equipment must be used only for the purpose it was designed for.
• The equipment must be used only for the purpose it was designed for.
• Abuse or misuse of the equipment is extremely dangerous for people, pets and property.
• Abuse or misuse of the equipment is
The manufacturer declines all responsibility for damage and injury resulting from improper
The manufacturer declines all responsibility for damage and injury resulting from
The manufacturer declines all responsibility for damage and injury resulting from
use and mishandling.
• Certain basic safety rules must be observed when using electrical equipment, in particular: -
• Certain basic safety rules must be observed when using electrical equipment, in particular:
• Certain basic safety rules must be observed when using electrical equipment, in particular:
Never touch the equipment with wet and/or damp hands or other parts of the body.
equipment with wet and/or damp hands or other parts of the body.
equipment with wet and/or damp hands or other parts of the body.
- Keep the equipment away from drops of water or sprinkling systems.
Keep the equipment away from drops of water or sprinkling systems.
- Never use the equipment near high heat sources or explosive material.
Never use the equipment near high heat sources or explosive material.
- Do not introduce any extraneous matter into the
Do not introduce any extraneous matter into the equipment.
- Do not allow children or untrained people to use the equipment.
Do not allow children or untrained people to use the equipment.
• Before cleaning or servicing the equipment outside, disconnect it from the supply and wait at
• Before cleaning or servicing the equipment outside, disconnect it from the supply and wait at
• Before cleaning or servicing the equipment outside, disconnect it from the supply and wait at
least 2 seconds before working on it, as recommended by current safety regulations
least 2 seconds before working on it, as recommended by current safety regulations
least 2 seconds before working on it, as recommended by current safety regulations.
• In the event of faults and/or improper operation, turn off the equipment, shut off the
• In the event of faults and/or improper operation, turn off the equipment, shut off the
• In the event of faults and/or improper operation, turn off the equipment, shut off the
electrical power and call your dealer.
electrical power and call your dealer.
• Do not attempt to make repairs and/or adjustments when covers/guards or circuit boards are
• Do not attempt to make repairs and/or adjustments when covers/guards or circuit boards are
• Do not attempt to make repairs and/or adjustments when covers/guards or circuit boards are
to be removed.
• Blown fuses inside the power supply indicate that there may be a fault in
de the power supply indicate that there may be a fault in the power supply
de the power supply indicate that there may be a fault in
itself. The fuses must be replaced by qualiied and authorised persons. It is advisable to call
itself. The fuses must be replaced by qualiied and authorised
your nearest dealer.
• Call your dealer for any repairs and be certain original spare
• Call your dealer for any repairs and be certain original spare parts are used.
Failure to observe this rule may adversely affect the safety level of your equipment
Failure to observe this rule may adversely affect the safety level of your equipment.
Failure to observe this rule may adversely affect the safety level of your equipment
• The equipment is to be connected to the mains supply and provided with
• The equipment is to be connected to the mains supply and provided with
• The equipment is to be connected to the mains supply and provided with adequate and
eficient earth conductors.
• The electrical wiring must be done in c
• The electrical wiring must be done in compliance with current electrical codes
"Electrical speciication for domestic buildings".
"Electrical speciication for domestic buildings".
• When installing, leave a clearance of at least 1 cm around the equipment to
• When installing, leave a clearance of at least 1 cm around the equipment to
• When installing, leave a clearance of at least 1 cm around the equipment to
allow air to pass freely.
NOTE. This piece of equipment has been manufactured
NOTE. This piece of equipment has been manufactured to the highest standards of
workmanship. It must be used
workmanship. It must be used properly and serviced as recommended to ensure
long-term dependable operation.
dependable operation.
The installation must be done in order to be able to guarantee an easy access to the cable of
The installation must be done in order to be able to guarantee an easy access to the cable of
The installation must be done in order to be able to guarantee an easy access to the cable of
feeding.
The device of dissection of the equipment is the cable of feeding, so it must be unconnected
section of the equipment is the cable of feeding, so it must be unconnected
section of the equipment is the cable of feeding, so it must be unconnected
from the equipment every time it is necessary to do any type of maintenance.
from the equipment every time it is necessary to do any type of maintenance.
from the equipment every time it is necessary to do any type of maintenance.
AEV Broadcast Srl – via della Tecnica 33 – 40050 Argelato (BO) Italy
AEV Broadcast
AEV SYNAPSE - ON AIR CONSOLE
ompliance with current electrical codes CEI 64-8
properly and serviced as recommended to ensure
Web site www.aev.eu
Web site
for people, pets and property.
persons. It is advisable to call
parts are used.
to the highest standards of
Argelato (BO) Italy
e-mail info@aev.eu
3
Advertisement
Table of Contents
