Summary of Contents for Kelley AQUASHIELD SYSTEM AQS-900 Series
Page 1
4Front Entrematic W183 S8253 Racine Avenue Muskego, WI 53150 Tel: (262) 679-6200 Email: seals.shelters@entrematic.com ® AQUASHIELD SYSTEM SERIES AQS-900 TUFSTEEL ® GALVANIZED STEEL FRAMING Installation Instructions FORM NO: 4F-AQS-3/19 PART NO: T31636 Do not install this product unless you read and understand the Warnings and Installation WARNING Instructions contained in this manual.
TABLE OF CONTENTS Introduction…………………………………………………………………………………………………………………………………….…...…2 Safety Signal Words…………………………………………………………………………………………………………………………..….…2 Safety Practice………………………………………….…………………………………………………………………………………………..…3 Preparation……………………………………………………………………………………………………………………………………………..3 Parts List Standard Components & Part Numbers....................4 Suggested Mounting Method…………………………………………………………………………………………………………..…4 Installation…………………………………………………………………………………………………………………………………………….…5 Exploded View…………..…..……………………………………………………………..……………………………………………………..…13 Attention & Maintenance ………………………………………………………………………………………………………………….…..14 Warranty information…………………………………………………………………………………………………………………………..15 Distributor Information………………………………………………………………………………………………………………………..…16 INTRODUCTION Welcome and thank you for choosing a dock seal/shelter from KELLEY®. This Installation Manual contains information that you need to safely install, operate and maintain the dock seal/shelter. Please keep and read this Installation Manual before installing and using your new dock seal/shelter. SAFETY SIGNAL WORDS You may find safety signal words such as DANGER, WARNING, CAUTION, or NOTICE throughout this Installation Manual. Their use is explained below: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Indicates an imminently hazardous situation which, if not avoided, will result in death or DANGER ...
READ AND FOLLOW THE OPERATING INSTRUCTIONS IN THIS MANUAL BEFORE OPERATING THE AQS‐900® If you do not understand the instructions, ask your supervisor to assist you or contact the factory. Be certain to follow the instructions in this manual. NOTICE KELLEY AQS‐900 series are custom built for each application. Installation procedures are the same for all AQS‐900 Series, regardless of size. Installation requires two people and a forklift truck or similar device to lift and position the frame. Improper installation of anchoring devices or installation into aged or unsound concrete or other faulty or inadequate building wall construction could result in serious injury or death, as well as premature product wear, product failure, or property damage. Inadequate lifting equipment or unsafe practices can cause a load to fall unexpectedly. Make sure lifting devices are in good condition and have a rated capacity of at least 500 lbs. at the lifting angle that they are being used. Never allow anyone to stand on or near the dock seal/shelter component when it is lifted or placed. Failure to follow this warning can allow the dock seal to fall, tip or swing into people causing serious injury or death. Safety standards as described in this installation manual must be followed at all times. If you have any questions, contact your supervisor or your local Kelley ...
ATTENTION & MAINTENANCE NOTICE Periodic inspections of all dock Seal/Shelter is recommend. Inspect for damage and contact your local distributor if parts are needed to be replaced. PERIODIC MAINTENANCE CHECKLIST Rips/tears in wiper pad fabric/cover Water leaks due to insufficient caulk Ensure steel head frame is plumb to building wall Ensure all fasteners are in position Ensure vinyl trim is secured to stop plate * * * POST INSTALLATION CHECK LIST Head Frame is perpendicular to building wall Ensure all anchors & fasteners are secured correctly Confirm the head frame is caulked at building adequately Bottom of head frame is installed at correct dimension off finished grade Confirm caulk is applied to the back side of the stop plate Side cover is attached to tab on head frame bracket Confirm vinyl trim is secured to stop plate Ensure wiper pad is straight and does not bend NOTES ...
This Limited Warranty does not cover any failure caused by improper installation, abuse, improper operation, negligence, or failure to maintain and adjust the DOCK SEAL/SHELTER properly. Parts requiring replacement due to damage resulting from vehicle impact, abuse, or improper operation and not covered by the warranty. Kelley® DISCLAIMS ANY RESPONSIBILITY OR LIABILITY FOR ANY LOSS OR DAMAGE OF ANY KIND (INCLUDING WITHOUT LIMITATION, DIRECT, INDIRECT, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR LOST PROFITS OR LOST PRODUCTION) arising out of or related to the use, installation or maintenance of the DOCK SEAL/SHELTER (including premature product wear, product failure, property damage or bodily injury resulting from use of ...
Please direct questions about your DOCK SEAL/SHELTER to your local distributor. Your local KELLEY® distributor is: 4Front Entrematic W183 S8253 Racine Avenue ...