Advertisement
HomeSpot
Bluetooth Adapter for
®
NSwitch
The Bluetooth
®
word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks
by HomeSpot
is under license.
®
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other
countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the
United States and other countries.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HomeSpot NSwitch HS3 NS001
Summary of Contents for HomeSpot NSwitch HS3 NS001
- Page 1 NSwitch The Bluetooth ® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by HomeSpot is under license. ® Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
-
Page 2: Package Contents
Package Contents HomeSpot HS3 NS001 User Guide USB-C to USB-A Adapter Mini Mic Pouch Warranty Card... - Page 3 About your HomeSpot HS3 NS001 P1 Button Press to Connect / Hold to Pair P1 LED On = Connected / Flashing = Connecting or Pairing* Codec LED USB-C Plug Off = SBC / Blue = aptX / Amber = aptX Low Latency...
-
Page 4: Setting Up Your Hardware
2. Insert the HomeSpot HS3 NS001 into the NSwitch USB-C port. 3. LED indictors on the HomeSpot HS3 NS001 will start flashing. 4. HomeSpot HS3 NS001 is ready for pairing and connecting with your headphones once the LEDs have stop flashing. - Page 5 Connecting to one Bluetooth headphones 1. Upon powering up, HomeSpot HS3 NS001 automatically enters pairing mode on first use. 2. Make sure the Bluetooth headphones is in pairing mode. 3. Keep the headphones close to the HS3 NS001 during initial pairing.
- Page 6 Connecting to two Bluetooth headphones 1. Pair and connect to the first headphones. 2. Pair the 2nd headphones by pressing the P2 button for 3 seconds. 3. Keep the 2nd headphones close to the HS3 NS001 during initial pairing. 4. Once the 2nd headphones is connected, the P2 LED will be on. 5.
- Page 7 Reconnecting to a previously paired headphones . Automatic re-connect When a previously paired headphones is turned on, it will automatically re-connect to the HomeSpot HS3 NS001. . Manual re-connect You may also manually initiate a re-connect by pressing either the P1 or P2 button, the corresponding previously paired 1st or 2nd headphones will be re-connected respectively.
- Page 8 TV Mode The HomeSpot HS3 NS001 can also be used with the TV dock. Simply plug the bundled USB-C to USB-A adapter to the USB-A port on the side of the TV dock, then insert the HS3 NS001 into USB-C port on the adapter.
-
Page 9: Led Indicators
LED Indicators Status LED Pattern Operation Powering ON Power on NSwitch and insert NS3 NS001 (LEDs flashing from left to right) Power OFF/ Standby Power off NSwitch or unplug NS3 NS001 P1 Pairing Hold P1 button for 3 secs P1 Connecting Press P1 button once P2 Pairing Hold P2 button for 3 secs... -
Page 10: Product Specification
Product Specification Bluetooth version Bluetooth 5.0 Operating Frequency 2402 – 2408MHz Supported Bluetooth Profiles A2DP Supported Codec aptX Low Latency, aptX and SBC Operating Range Up to 10 meters line of sight Operating Temperature Range 0˚C to 45˚C Safety Instructions .
Need help?
Do you have a question about the NSwitch HS3 NS001 and is the answer not in the manual?
Questions and answers