LARGE CANNISTER SPEAKER
CAPSULE IPX6
HRSP 5020
The Bluetooth
®
word mark and logos are registered trademarks owned by Bluetooth
any use of such marks by The Source (Bell) Electronics Inc. is under license. Other trademarks and
trade names are those of their respective owners.
FEATURES:
1. Bluetooth
4.2
®
2. Hands-free telephone calling
3. True Wireless Stereo (TWS) pairing
4. Bluetooth
operating distance up
®
to 10m (33ft.)
5. TWS pairing distance up to 8m (26ft.)
6. Playtime up to 6-8 hours
(varies by volume level and content)
7. Battery charge time between 2.5-3 hours
8. Water-resitant rating IPX6
PRODUCT OVERVIEW
You can use this item with any compatible, Bluetooth
stream music and enjoy hands-free calling. Please read this manual fi rst
before using. This unit has IPX6 rating: Protected against heavy seas – Water
projected at all angles through a 12.5mm nozzle at a fl ow rate of 100 litres/
minute at a pressure of 100kN/m2 for 3 minutes from a distance of 3
metres/10 feet. DO NOT submerge in water.
OPERATING INSTRUCTIONS
TO
Press and hold the
Power ON
and the LED will turn ON.
Press and hold the
Power OFF
and the LED will turn OFF.
Adjust the volume
Press the +/- buttons.
Play/Pause
Press the
Next track
Press and hold the + button.
Previous track
Press and hold the - button.
Bluetooth
mode/AUX-in mode
Press the
®
Answer a call
Press the
Reject a call
Press and hold the
End a call
Press the
Redial last-called number
Press and hold the
CHARGING
Use the included micro USB charging cable to fully charge the speaker before
fi rst use. It will take approximately 2.5-3 hours to fully charge. The micro
USB cable can be plugged in to a computer or with a USB AC adapter (not
included).
• The LED will fl ash red and the speaker will beep once every 40 seconds
when the battery falls below 10%
• The LED will turn solid red while the speaker is charging
• The LED will turn solid green once charging is complete
• Unplug the speaker once it is fully charged
• If the battery falls below 3%, the speaker automatically powers OFF
PAIRING
Make sure that the speaker is within 10m (33ft.) of your device.
1. Press and hold the
button until you hear an ascending tone, and the
LED will begin fl ashing blue.
2. Turn the Bluetooth
ON in your device settings and select
®
"HR CAPSULE".
3. Once paired successfully, the LED will turn solid blue.
4. To disconnect from a paired device, press and hold the +/- buttons
simultaneously until you hear a tone. The LED will quickly fl ash blue,
signalling it is ready to be paired with a new Bluetooth
NOTE: The next time you turn the speaker ON, it will connect automati-
cally as long as the Bluetooth
®
range. If no device is paired within 10 minutes, the speaker's Bluetooth
pairing will turn OFF to conserve energy.
COMPONENT IDENTIFICATION:
1. Next track/Increase volume
2.
Play/Pause
3. Previous track/Decrease volume
4.
Power ON/OFF
5. AUX-IN port (3.5mm)
6. Micro USB charging port
-enabled device to
®
DO THIS
button. You will hear an ascending tone
button. You will hear a descending tone
button once to pause. Press again to resume.
button.
button.
button.
button.
button.
device.
®
on your device is switched ON and is within
®
SIG, Inc. and
HANDS-FREE SPEAKERPHONE
When a smartphone is connected to your speaker, follow the steps below to
take calls hands-free.
1. If there is an incoming call while streaming music, you will hear the phone
ring through the speaker.
2. Press the
3. Press the
AUX-IN MODE
1. Power ON the speaker.
2. Using the AUX cable (3.5mm), connect your external device to the
speaker's AUX-IN port.
3. Automatically switches to AUX-IN mode, and the LED turns solid green.
NOTE: In AUX-IN mode, the functions for skipping songs and answering
calls on speakerphone are disabled.
TRUE WIRELESS STEREO (TWS) FUNCTION
Connect two large cannister speakers via Bluetooth
Stereo experience.
1. Turn both speakers ON and place them within 8m (26ft.) of each other.
2. On one of the speakers, double press the
LED fl ashes blue and green. It is now in a stereo-pairing mode.
3. After 3-5 seconds, if the speakers successfully pair, the primary speaker's
LED will fl ash blue and the secondary speaker's LED will turn solid blue.
4. To disconnect, press and hold the +/- buttons simultaneously until the
LED fl ashes blue.
NOTE: In TWS mode, calls can only be answered through the primary
speaker.
UNDERSTANDING THE LED STATUS LIGHTS
• When your speaker's battery is low
o LED fl ashing red=battery below 10%
• When charging your speaker
o Solid red LED=charging
o Solid green LED=charging complete
• When pairing your speaker to a Bluetooth
o Quick-blinking blue LED=Bluetooth
o Solid blue LED=Bluetooth
• When pairing your speaker to a Bluetooth
o LED fl ashing blue and green=Searching for TWS pairing
o LED fl ashing blue on the main speaker, and solid blue LED on the
secondary speaker=TWS connected, Bluetooth
• When connecting via AUX IN
o Solid green LED=connected
®
WHAT'S INCLUDED:
• Speaker
• Micro USB cable
• 3.5mm audio cable
• Instruction Manual
• Carry strap
1.
2.
3.
4.
button to pick up the call.
button again to hang up the call.
not connected, ready to pair
®
connected
®
8080297
INSTRUCTION MANUAL
5.
6.
for a True Wireless
®
button for 2 seconds until the
device
®
device in TWS mode
®
waiting for pairing
®
Need help?
Do you have a question about the HRSP 5020 and is the answer not in the manual?
Questions and answers