Advantech ADAM-4515 Manual

S E R I A L S E R I A L S E R I A L C O M M U N I C A T I O N C O M M U N I C A T I O N C O M M U N I C A T I O N
S E R I A L S E R I A L C O M M U N I C A T I O N C O M M U N I C A T I O N
ADAM-4515
Isolated CAN Repeater
Introduction
Most industrial computer systems come with
standard RS-232 serial ports. Though widely
used and accepted, RS-232 connections have
limited transmission speed and networking
capabilities. CAN (Controller Area Network) is a
serial bus system with multimaster and real-time
capability. It is a cost-effective Fieldbus for
device networking in manufacturing plants. The
ADAM-4515 repeater is a family of products that
extend a communication cable's length in CAN
V2.0 systems. By allowing the user to extend the
bus length at any given speed, ADAM-4515
repeaters assist the user to cost-effectively
implement I/O or other nodes on these buses at
remote locations. Implementing I/O or other
nodes without an ADAM-4515 would be more
difficult and expensive. The ADAM-4515
repeater simply amplifies or boosts existing CAN
signals to enable them to cover long distances
from 40 m to 1000 m according to the data
transfer rate. ADAM-4515 repeaters also allow
users to increase the maximum number of
connected nodes up to 64.
Features
• Expands the usefulness of CAN-bus systems
Enables faster operation over longer
•
distances
Supports speeds up to 1 Mbps for CAN
•
Automatic speed selection - no configuration
•
required
Transmission distance = 80 m at 1 MHz, up to
•
1000 m depending on baud rate
Jumper selected
•
Power and data flow indicator for trouble shooting
•
Power requirements: +10 to +30 V
•
Mounts easily on DIN-rail or panel
•
ADAM and the ADAM logo are trademarks of Advantech.
I N T E R F A C E I N T E R F A C E I N T E R F A C E
I N T E R F A C E I N T E R F A C E

Specifications

•
•
•
•
•
•
•
•
•
•
•
•
Function diagram
Master
DC
Part no. 2000451500
F O R F O R F O R I N D U S T R I A L I N D U S T R I A L I N D U S T R I A L
F O R F O R I N D U S T R I A L I N D U S T R I A L
Power requirements
Unregulated +10 to +30 V
power reversals
Case: ABS with captive mounting
Accessories (included):
- Nylon DIN-rail mounting adapter
- SECC panel mounting bracket
- Plug-in screw terminal wiring :
Accepts AWG 1-#12 to #22 ( 0.5 to 2.5mm) wires
Baud rate: up to 1Mbps (automatic selection)
Address selection: not applicable
Bus connection
- Repeater:
5-pin male header 2.5/5-ST-5.08/AU (included)
- CAN-bus:
5-contact female plug 2.5/5-ST-5.08/AU (included)
Status indicators
Module status: green/red bi-color LED
Network status: green/red bi-color LED
Maximum power:
Voltage: +10 to 30 V
DC
Current: 140 mA @ 11 V
20 mA @ 11 V , 10 mA @ 25 V
DC
Power: 1 W
Operating temperature: -10 to 70° C
Dimensions: 2.36" x 4.41" ( 60 mm x 120
mm )
Network left
T
I/O nodes
1st Edition
A U T O M A T I O N A U T O M A T I O N A U T O M A T I O N
A U T O M A T I O N A U T O M A T I O N
with protection from
DC
, 60 mA @ 25 V ,
DC DC
DC
Network right
A
T
B
I/O nodes I/O nodes
Printed in Taiwan Apr 1998