Related Manuals for P.Audio CXP Series
Summary of Contents for P.Audio CXP Series
- Page 1 P.Audio System Co., Ltd CXP Series CXP-21Sub: 2000w (Peak) Active 21” Subwoofer CXP-121C: 2000w (Peak) Active 12” Coaxial Speaker CXP-151C: 2000w (Peak) Active 15” Coaxial Speaker...
- Page 2 Protect the AC Mains power cord from being walked on or otherwise damaged and inspect for damaged connections and damaged insulation. The CXP Series may be suspended, with the exception of CXP-21Sub. DO NOT SUSPEND THE CXP-21Sub 10. DO NOT SUBSTITUTE SUSPENSION HARDWARE.
-
Page 3: Table Of Contents
The P.Audio CXP-21Sub brings a new level of performance to both portable and installed sound in the form of the large 21” inch woofer, which provides extreme low end, high power handling and very high sound pressure level capabilities, whilst using all of P.Audio’s expertise in world class component design to ensure very high reliability. -
Page 4: Specifications
0C-43C / 32F- 0C-43C / 32F- 0C-43C / 32F- 110F 110F 110F * NOTE: Max Acoustic Output is based on smoothed system response, not peak driver response. P.Audio is continually looking to improve products, so specifications are subject to change without notice. -
Page 5: Setup And Use Of The Cxp Products
Leave enough slack to allow for accidents. In order to use the power link feature on the CXP series cabinets, a separate powercon cable must be purchased. This cable will have a powercon output and powercon input connector on either end. -
Page 6: Audio Connections
NOTE: If the pilot light does not illuminate within 30 seconds the unit may be in a FAULT CONDITION. If this occurs, the unit should be returned to P.Audio for evaluation. THERE ARE NO USER-SERVICABLE PARTS INSIDE. DO NOT REMOVE THE AMPLIFIER MODULE! (See the section below “Replacement of Components”... -
Page 7: Remote Software - Dsp.audio
UDIO The remote control software enables the user to adjust EQ, delay, polarity, noise gates and other aspects of the CXP series enclosures performance. Once the unit is connected to the computer, any changes made on the computer will become active, but will NOT be saved onto the amplifier, until the preset is stored onto the CXP series amplifier. -
Page 8: Controlling The Cxp Series Speakers
4.4. CONTROLLING THE CXP SERIES SPEAKERS Once the software is up and running, all connected speakers will be seen in the ID list to the left hand side of the screen. All parameters available to the user will be available by double clicking the device required to monitor, and the parameters screen will be displayed. -
Page 9: Protection
DLF – DLF is a set of filters tuned specifically to make recorded music sound more dynamic at low levels. In the ‘music’ presets on the amplifier, this option is turned on. High Pass Filter – All of the cabinets already have a high pass filter programmed in, but an extra high pass filter is provided to the user for crossover, or extra subsonic filtering. -
Page 10: Rigging And Suspension
WARNING: The pole used to mount the mid-hi enclosure must NOT be more than 0.8 meters (31.5 inches) long. DO NOT use a pole that is longer than 0.8 meters! DO NOT PLACE ANY OTHER LOUDSPEAKERS, EXCEPT THE CXP SERIES on the CXP-21Subs POLE. -
Page 11: Product Service
MODULE MUST NOT BE SET DOWN ON THE COMPONENT SIDE OR DAMAGE WILL OCCUR! NOTE: The powered models in the CXP series feature an internal fuse to protect the power amplifier. THE INTERNAL FUSE IS NOT USER REPLACABLE. UNDER NO CIRCUMSTANCES SHOULD THE AMPLIFIER PANEL BE REMOVED FROM... - Page 12 Thank you once again for purchasing this P.Audio product. P.Audio is a manufacturer of a complete range of Loudspeaker systems, individual components and accessories. For more information regarding any of P.Audio’s products or advice on how to set up and use this product, please do not hesitate to use the contact details on the following page to contact us.