Synchronizing rfid long range readers using the digital in-/outputs (27 pages)
Summary of Contents for Feig Electronic OBID i-scan ID ISC.LRMU1000
Page 1
MONTAGE ® OBID i-scan INSTALLATION ID ISC.LRMU1000 ID ISC.LRU1000-M (deutsch / english) public (B) 2006-05-30 M41200-2de-ID-B.doc...
Page 2
® OBID i-scan Montage / Installation ID ISC.LR(M)U1000 deutsche Version ab Seite 3 english version from page 28 FEIG ELECTRONIC GmbH Seite 2 von 52 M41200-2de-ID-B.doc...
Page 3
Hinweise jederzeit dankbar. Die in diesem Dokument gemachten Installationsempfehlungen gehen von günstigsten Rahmenbedingun- gen aus. FEIG ELECTRONIC GmbH übernimmt weder Gewähr für die einwandfreie Funktion in system- fremden Umgebungen, noch für die Funktion eines Gesamtsystems, welches die in diesem Dokument be- schriebenen Geräte enthält.
2.9.2 RS485/RS422 Schnittstelle ...................17 2.9.3 Netzwerkanschluss .......................18 2.9.4 CompactFlash-Steckplatz (nur Gerätevarianten mit ACC)..........18 Bedien- und Anzeigeelemente LEDs ..........................19 Taster / Schalter ......................20 Inbetriebnahme Schnittstellenkonfiguration ..................21 4.1.1 RS485/RS422 .......................21 4.1.2 Netzwerkanschluss - LAN .....................23 FEIG ELECTRONIC GmbH Seite 4 von 52 M41200-2de-ID-B.doc...
Page 5
® OBID i-scan Montage / Installation ID ISC.LRU1000 Funkzulassungen Europa (CE)........................24 USA (FCC) ........................24 Technische Daten FEIG ELECTRONIC GmbH Seite 5 von 52 M41200-2de-ID-B.doc...
Page 6
Obwohl dieses Gerät die zulässigen Grenzwerte für elektromagnetische Felder nicht über- schreitet, sollten Sie einen Mindestabstand von 25 cm zwischen dem Gerät und Ihrem Herz- schrittmacher einhalten und sich nicht für längere Zeit in unmittelbarer Nähe des Geräts bzw. der Antenne aufhalten. FEIG ELECTRONIC GmbH Seite 6 von 52 M41200-2de-ID-B.doc...
Beschreibung ID ISC.LRMU1000-A-EU Gerätevariante ohne ACC für Europa ID ISC.LRU1000-M-A-EU Gerätevariante mit ACC für Europa ID ISC.LRMU1000-A-FCC Gerätevariante ohne ACC für USA ID ISC.LRU1000-M-A-FCC Gerätevariante mit ACC für USA Tabelle 2-1: Readermodultypen FEIG ELECTRONIC GmbH Seite 7 von 52 M41200-2de-ID-B.doc...
® OBID i-scan Montage / Installation ID ISC.LR(M)U1000 2.3 Montage Zur Befestigung des Readers befinden sich auf der Montageplatte (schraffiert) vier Durchbrüche. Bild 2-1: Reader mit Montageplatte FEIG ELECTRONIC GmbH Seite 8 von 52 M41200-2de-ID-B.doc...
Vcc - Versorgungsspannung X13 / Pin 2 Ground – Versorgungsspannung Tabelle 2-3: Pinbelegung Versorgungsspannung ID ISC.LRU1000 Bild 2-3: Anschluss der Versorgungsspannung Hinweis: • Eine Verpolung der Versorgungsspannung kann zur Zerstörung des Gerätes führen. FEIG ELECTRONIC GmbH Seite 10 von 52 M41200-2de-ID-B.doc...
Beschreibung Kollektor – Ausgang 1 Emitter – Ausgang 1 + Eingang 1 - Eingang 1 Tabelle 2-4: Pinbelegung Optokoppler ID ISC.LRU1000 ext. ext. Bild 2-4: Interne und mögliche externe Beschaltung der Optokoppler FEIG ELECTRONIC GmbH Seite 11 von 52 M41200-2de-ID-B.doc...
Page 12
Hinweise: • Der Eingang ist für eine maximale Eingangsspannung von 24 V DC und einem Ein- gangsstrom von maximal 20 mA ausgelegt. • Verpolung oder Überlastung des Eingangs führt zu dessen Zerstörung. FEIG ELECTRONIC GmbH Seite 12 von 52 M41200-2de-ID-B.doc...
• Der Relaisausgang ist nur zum Schalten ohmscher Lasten vorgesehen. Im Falle einer induktiven Last sind die Relaiskontakte durch eine externe Schutzbeschaltung zu schüt- zen. ext. ID ISC.LRU1000 Bild 2-5: Interne und mögliche externe Beschaltung des Relaisausgangs FEIG ELECTRONIC GmbH Seite 13 von 52 M41200-2de-ID-B.doc...
Mit der Readersynchronisation können verschiedene Aktionen der Reader synchronisiert werden. Klemme Kurzzeichen Beschreibung - Eingang + Eingang - Ausgang +Ausgang Tabelle 2-7: Pinbelegung Readersynchronisation ID ISC.LRU1000 OUT+ (Z) OUT- (Y) IN+ (B) IN- (A) Bild 2-6: Eingang und Ausgang der Synchronisation FEIG ELECTRONIC GmbH Seite 14 von 52 M41200-2de-ID-B.doc...
Bild 3.7-1: Anschluss externer LEDs an X14 Hinweis: • Die Ausgänge an X14 sind nur zum Schalten einer externen LED vorgesehen. Überlas- tung der Ausgänge durch andere Lasten kann zu deren Zerstörung führen. FEIG ELECTRONIC GmbH Seite 15 von 52 M41200-2de-ID-B.doc...
Die Übertragungsparameter können per Softwareprotokoll konfiguriert werden. Anschlussbelegung X8 (RS232-Schnittstelle): Klemme Kurzzeichen Beschreibung RS232 – GND RS232 - RxD RS232 - TxD Tabelle 2-9: Pinbelegung RS232-Schnittstelle Bild 2-7: Verdrahtungsbeispiel für den Anschluss der RS232-Schnittstelle FEIG ELECTRONIC GmbH Seite 16 von 52 M41200-2de-ID-B.doc...
Receive Data - VETH- n.c. VETH- n.c. Tabelle 2-11: Pinbelegung Ethernet-Schnittstelle 2.9.4 CompactFlash-Steckplatz (nur Gerätevarianten mit ACC) Der Reader verfügt über einen CF2-Steckplatz (Stecker X12). Dieser Steckplatz für zukünftige Erweiterungsmöglichkeiten durch CompactFlash-Karten vorgesehen. FEIG ELECTRONIC GmbH Seite 18 von 52 M41200-2de-ID-B.doc...
Leuchtet bei einem Fehler im RF-Teil des Readers. Der Feh- lertyp kann per Software über die RS232/RS485-Schnittstelle ausgelesen werden LED V6 (grün) "RUN-LED 2" (Nur ID Signalisiert den ordnungsgemäßen Ablauf des ISC.LRU1000-G) Controllers Tabelle 3-1: Konfiguration der LED FEIG ELECTRONIC GmbH Seite 19 von 52 M41200-2de-ID-B.doc...
3.2 Taster / Schalter Kurzzeichen Beschreibung Reset-Taster RF Controller Reset-Taster ACC Reserviert T1: Durch betätigen von T1 wird am RF-Controller ein Reset durchgeführt T2: Durch betätigen von T2 wird am ACC ein Reset durchgeführt FEIG ELECTRONIC GmbH Seite 20 von 52 M41200-2de-ID-B.doc...
Pull-Down an RS422 - Y ohne Pull-Down an RS422 – Y Abschlusswiderstand ohne Abschlusswiderstand RS422 - Y ⇔ RS422 - Z RS422 - Y ⇔ RS422 - Z Tabelle 4-2: Abschlusswiderstände der RS485/RS422 FEIG ELECTRONIC GmbH Seite 21 von 52 M41200-2de-ID-B.doc...
Page 22
Tabelle 4-3 zeigt die Standardkonfiguration der Jumper J9 bis J12. Diese sind für die RS485 und RS422 identisch. Jumper LRU1000-G LRU1000-M geschlossen offen geschlossen geschlossen offen offen offen geschlossen Tabelle 4-3: Standardkonfiguration der RS485/RS422 FEIG ELECTRONIC GmbH Seite 22 von 52 M41200-2de-ID-B.doc...
IP-Adresse verfügt. Alle Reader verfügen über eine werksseitig voreingestellte IP- Adresse. Die Reader müssen nacheinander ans Netzwerk angeschlossen und konfiguriert werden. Tabelle 3-1 zeigt die Standardkonfiguration des Netzwerkanschlusses. Netzwerk Adresse IP-Adresse 192.168.10.10 Subnet-Mask 255.255.255.0 Port 10001 Tabelle 4-4: Standardkonfiguration des Netzwerkanschlusses FEIG ELECTRONIC GmbH Seite 23 von 52 M41200-2de-ID-B.doc...
Page 24
Commission Rules permitting the operation of this device. Warning: Changes or modification made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. FEIG ELECTRONIC GmbH Seite 24 von 52...
Page 25
Eingänge - 1 Optokoppler max. 24 V DC/ 20 mA - 1 Differenzeingang Reader Synchronisation • Schnittstellen - RS232 - RS484 / RS422 (wahlweise einstellbar) - Ethernet (TCP/IP) (Nur Gerätevariante mit ACC) FEIG ELECTRONIC GmbH Seite 25 von 52 M41200-2de-ID-B.doc...
Page 26
Zulassung Funk - Europa EN 302 208 - USA EN 300 220 FCC 47 CFR Part 15 • EN 301 489 • Sicherheit - Niederspannung EN 60950 - Human Exposure EN 50364 FEIG ELECTRONIC GmbH Seite 26 von 52 M41200-2de-ID-B.doc...
Page 28
FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed with components and testing methods for a level of reliability suitable for use in or in connection with surgical implants or as critical components in any life support systems whose failure to perform can reasonably be expected to cause significant injury to a human.
Page 29
2.9.3 Network connection.......................44 2.9.4 CompactFlash Slot (only device version with ACC) ...........44 Operating and Display Elements LEDs ..........................45 Buttons / Switches ......................46 Startup Interface configuration....................47 4.1.1 RS485/RS422 .......................47 4.1.2 Network connection - LAN.....................49 FEIG ELECTRONIC GmbH Page 29 of 52 M41200-2de-ID-B.doc...
Page 30
® OBID i-scan Installation ID ISC.LRU1000 Radio Approvals Europe (CE)........................50 USA (FCC) ........................50 Technical Data FEIG ELECTRONIC GmbH Page 30 of 52 M41200-2de-ID-B.doc...
Page 31
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in the immediate proximity of the device’s antenna for any length of time. FEIG ELECTRONIC GmbH Page 31 of 52 M41200-2de-ID-B.doc...
Device version without ACC for Europe ID ISC.LRU1000-M-A-EU Device version with ACC for Europe ID ISC.LRMU1000-A-FCC Device version without ACC for USA ID ISC.LRU1000-M-A-FCC Device version with ACC for USA Table 2-1: Reader types FEIG ELECTRONIC GmbH Page 32 of 52 M41200-2de-ID-B.doc...
® OBID i-scan Installation ID ISC.LRU1000 2.3 Installation To mount the reader there are four drilled holes in the mounting plate (hatched). Fig. 2-1: Reader witch mounting plate FEIG ELECTRONIC GmbH Page 33 of 52 M41200-2de-ID-B.doc...
The maximum tightening torque for the SMA sockets is 0.45 Nm. Caution: Exceeding the tightening torque will destroy the plug. Terminal Description X1, X2 Connection for external antennas X3, X4 (input impedance 50Ω) Table 2-2: External antenna connection FEIG ELECTRONIC GmbH Page 35 of 52 M41200-2de-ID-B.doc...
X13 / Pin 2 Ground – supply voltage Table 2-3: Pinouts for supply voltage ID ISC.LRU1000 Fig. 2-3: Connecting the supply voltage Note: • Reversing the supply voltage polarity may destroy the device. FEIG ELECTRONIC GmbH Page 36 of 52 M41200-2de-ID-B.doc...
Collector – Output 1 Emitter – Output 1 + Input 1 - Input 1 Table 2-4: Optocoupler pinouts ID ISC.LRU1000 ext. ext. Fig. 2-4: Internal and possible external wiring of the optocouplers FEIG ELECTRONIC GmbH Page 37 of 52 M41200-2de-ID-B.doc...
Page 38
The input is configured for a maximum input voltage of 24 V DC and an input current of max. 20 mA. • Polarity reversal or overload on the input will destroy it. FEIG ELECTRONIC GmbH Page 38 of 52 M41200-2de-ID-B.doc...
• The relay output is intended for switching resistive loads only. If an inductive load is connected, the relay contacts must be protected by means of an external protection circuit. ext. ID ISC.LRU1000 Fig. 2-5: Internal and possible external wiring of the relay output FEIG ELECTRONIC GmbH Page 39 of 52 M41200-2de-ID-B.doc...
1 3 5 Fig. 3.7-1: Connecting external LEDs to X14 Note: • The outputs on X14 are intended for switching an external LED only. Overloading the outputs with other loads may destroy them. FEIG ELECTRONIC GmbH Page 41 of 52 M41200-2de-ID-B.doc...
The transmission parameters can be configured by means of software protocol. Pin configuration X8 (RS232 interface): Terminal Abbreviation Description RS232 – GND RS232 - RxD RS232 - TxD Table 2-9: RS232 interface pinouts Fig. 2-7: Wiring example for connecting the RS232 interface FEIG ELECTRONIC GmbH Page 42 of 52 M41200-2de-ID-B.doc...
VETH- n.c. Table 2-11: Ethernet interface pinouts 2.9.4 CompactFlash Slot (only device version with ACC) The Reader has a CF2 slot (connector X12). This slot is for future use by CompactFlash cards. FEIG ELECTRONIC GmbH Page 44 of 52 M41200-2de-ID-B.doc...
Reader. The error type can be read out via software over the RS232/RS485 interface LED V6 (green) "RUN-LED 2" (ID ISC.LRU1000- Indicates proper running of the controller G only) Table 3-1: LED configuration FEIG ELECTRONIC GmbH Page 45 of 52 M41200-2de-ID-B.doc...
Pull-Down on RS422 - Y without Pull-Down on RS422 – Termination resistor without Termination resistor RS422 - Y ⇔ RS422 - Z RS422 - Y ⇔ RS422 - Z Table 4-2: Termination resistors for RS485/RS422 FEIG ELECTRONIC GmbH Page 47 of 52 M41200-2de-ID-B.doc...
Page 48
Tabelle 4-3 shows the standard configuration of jumpers J9 through J12. These are identical for RS485 and RS422. Jumper LRU1000-G LRU1000-M closed open closed closed open open open closed Table 4-3: Standard configuration for RS485/RS422 FEIG ELECTRONIC GmbH Page 48 of 52 M41200-2de-ID-B.doc...
The Readers must be connected and configured one after the other. Tabelle 3-1 shows the standard configuration of the network connection. Network Address IP address 192.168.10.10 Subnet mask 255.255.255.0 Port 10001 Table 4-4: Standard configuration of the network connection FEIG ELECTRONIC GmbH Page 49 of 52 M41200-2de-ID-B.doc...
Page 50
Commission Rules permitting the operation of this device. Warning: Changes or modification made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. FEIG ELECTRONIC GmbH Page 50 of 52...
Page 51
- 1 optocoupler max. 24 V DC/ 20 mA - 1 differential input Reader synchronization • Interfaces - RS232 - RS484 / RS422 (selectable) - Ethernet (TCP/IP) (only device version with ACC) FEIG ELECTRONIC GmbH Page 51 of 52 M41200-2de-ID-B.doc...
Page 52
RF approval - Europe EN 302 208 EN 300 220 FCC 47 CFR Part 15 - USA • EN 301 489 • Safety - Low-Voltage EN 60950 - Human Exposure EN 50364 FEIG ELECTRONIC GmbH Page 52 of 52 M41200-2de-ID-B.doc...