Advertisement
Quick Links
Instructions of shipment, unpacking and installation.
Terrace awning Jupiter
General scheme of terrace awning
roller tube support
arm bracket
Steering:
[ ] Manual,
[ ] E-drive,
[ ] Motor drive with NHK
Data of electric drive:
Power ............. W, Voltage 230V;
Frequency 50Hz;
YOC: .......................................
Serial Number: ........................
CAUTION!
These instructions must be read and understood before installation, adjustment,
service or maintenance.
Operations and Maintenance,
awning sheathing
support bar
mounting bracket
front profile
folding arm
.......................................
EN 13561
External blinds
Class of wind resistance:
.......................................
page: 1 / 20
Advertisement
Related Manuals for Jalousie-Welt Jupiter
Summary of Contents for Jalousie-Welt Jupiter
- Page 1 CAUTION! These instructions must be read and understood before installation, adjustment, service or maintenance. Operations and Maintenance, Instructions of shipment, unpacking and installation. Terrace awning Jupiter General scheme of terrace awning roller tube support awning sheathing front profile arm bracket...
- Page 2 page: 2 / 20 Content 1. Introduction 2. Instructions for use and maintenance 3. Transportation, unpacking and installation instructions Introduction These installation instructions are an integral part of the terrace awning and was written for the professionals of the installation company and for the end users. An additional instruction for the electric products will be attached to this manual and should be treated as an integral part of this instruction.
- Page 3 page: 3 / 20 Use and Maintenance instruction 2.1. General CAUTION! For the reasons of safety, installation, maintenance and use of awnings, please follow the following guidelines. The installation of the awning should be done by an authorized dealer. Modifying the construction of the awning are not allowed. The arms are under high spring tension.
- Page 4 page: 4 / 20 Always switch off the power supply before making any maintenance work. Switch should be placed in such a place where we can see the awning position in any movement. Switch should be located away from moving parts. Switch should be installed at a height according to the regulation for the disabled persons (generally less than 1,30 m).
- Page 5 page: 5 / 20 3.5. Disassembly and disposal Disassembly of the awning must be performed by qualified personnel. Awning contains no hazardous components. Turn to recycling company to reduce the negative influence of waste over the natural environment. 3.6. Important notes and warnings CAUTION! Roll up the awning in bad weather such as frost, snow, rain and hail.
- Page 6 page: 6 / 20 CAUTION! At angle of inclination of the awning at less than 14°, even during light rain, the awning must be roll up in order to prevent the damage caused by the bad weather conditions. Note Fabric in the terrace awnings is narrower (from 10 to 15 cm) than the total width of the awnings frame;...
- Page 7 page: 7 / 20 Instructions of shipment, unpacking and installation 3.1. Delivery 1x Terrace awning Type: Weekend EVO, Brackets ordered in accordance by the Type (Wall-, Ceiling- or Rafterin an amount according to the Table: Dimensions (cm) Depth: 220 - 365 Depth: 366 - 480 Depth: 481 - 600 Width: 150 - 200...
- Page 8 page: 8 / 20 3.4. Installation of the awnings frame CAUTION! Installation of awning or adjustment can be made only by trained installation team. The installation must be in accordance with the requirements of safety, particular in health and safety regulations.
-
Page 9: Check Delivery
page: 9 / 20 3.8. Installation steps Note Installation of awning or adjustment can be made only by trained installation team. 3.8.1. Check the delivery. 3.8.2. Mark and fix the mounting brackets. 3.8.3. Drill a cable conduit for electric line (only for motor drive). 3.8.4. - Page 10 page: 10 / 20 Awning is supplied with brackets for installation in wall, ceiling or roof rafters - in accordance with the contract. Type od installation Mounting brackets Installation Scheme Wall- Ceiling- Roof rafters - (wall mounting brackets + adapter) Wall assembly with hood...
- Page 11 page: 11 / 20 The awning meets the wind class rating when the manufacturer's recommended number and type of the mounting brackets were mounted with the correct mounting anchors. Before starting installation make sure that the mounting surface is suitable for the mounting ‒ if were found the deviations of the surface strength, then order more mounting brackets - (number of mounting brackets ,in standard, for Wall mounting Concrete C20/25).
- Page 12 page: 12 / 20 Check holes in the wall with the level and plumb- line. Each brackets were mounted with appropriate fasteners. For the surface made of concrete C20/25 use an approved anchors M12. Resistance force data: Permissible tensile load: F (kN) >=C20/25: 5,70 Permissible in the concrete compression zone: F (kN) >= C20/25: 6,50...
- Page 13 page: 13 / 20 If the awning were hanged in brackets, the hood Profile "Y" must be raised enough to easily put up the awning in the brackets. Awning put up in the brackets and insert supporting tubes in the lane.
- Page 14 page: 14 / 20 CAUTION! Pitch angle progressively regulate for all arms so that they do not lead to significant differences in the settings. Note Work will be performed on each arm. This work must be carried out by two people. Unroll Awning to the end to get the awning fabric taut.
- Page 15 page: 15 / 20 Person "2" ‒ if desired pitch angle is achieved, tighten the screw "B". After changing the pitch angle of the arms,the front profile requires the setting. Description of the system below. Note In order to prevent an accumulation of water from the rain in the fabric (a water bag forming), it is necessary to set by fully opened awning a pitch angel on more than 14 °.
- Page 16 page: 16 / 20 Fabric awning unroll till it drops to arms(for motor drive must set end point position). Fabric awning drops freely Unscrew the Clamping screws „G” on all arms. Set the slope at the cog "F " in any arms at the same slit "E". Be sure that the cog "F"...
- Page 17 page: 17 / 20 3.8.8. Using handle (only manual drive or motor drive with NHK) Awnings handle into the loop of the gearbox. By turning the handle can open or close the awning. Awning fabrics must be roll up on the right side (from top) otherwise it can damage the sheathing and the awning.
- Page 18 page: 18 / 20 3.9.1. Replacement a drive In order to make a repair to a defective drive, the awning must be using a belt secured. All the necessary work can be made only by a specialist. The drive must be the same series and by the same manufacturer are.
- Page 19 page: 19 / 20 3.12. Assembly drawing of the awning 3 4 5 (29) 6 III. 21 20 19 18 label roller tube support gearbox of manual drive, if ordered (on the left or right side of the awning) end of the roller tube or mounting position of the electric drive roller tube support bar ceiling bracket...
- Page 20 page: 20 / 20 lower part of the hing cables adjustment screws upper part of the hinge arm upper profile of the arm upper end of the arm III. Arm bracket adjustment handle of the arm adjustment screws C adjustment screws B screw (do not use!) arm holder roller tube holder...