Advertisement
8.
Secure to section
Ensure the fixing plate is aligned correctly.
Carefully drill two f3.5mm holes through the
countersunk holes in the fixing plate and
through the wall of the door/window section.
Secure the fixing plate to the aluminium
door/window section using the two
G8 x 1/2 AB CSK screws provided.
NOTE: Do not over-tighten.
fixing plate
door/window
section
G8 x 1/2 AB
CSK screws
Double Shoot-Bolt - CARE & MAINTENANCE
Installation
The product must be installed according to the instructions included in the product packaging and the
door/window should be apertured according to the door/window "cut-out" dimensions and tolerances shown.
Prior to fitting ensure that:
· Doors and windows stored on site are stored in a clean dry area free from cement, lime, paint, acid etc.
During fitting of the lock ensure that :
· No metal swarf or other contaminants enter the lock body.
· The fixing screws do not damage the product finish.
After installation of the door/window ensure that:
· The door/window is correctly adjusted with the correct clearances.
· The bolt tips operate freely with minimal effort.
· The door/window is protected from building fall-out such as wet plaster, mortar, paint and welding splatter.
If the door becomes contaminated:
· Do not paint the lock body or faceplate.
· Remove wet plaster, cement, mortar and other droppings immediately, using ample clean water and a sponge or rag, to avoid permanent
staining or scratching of the product finish. If removal is delayed and scraping becomes necessary the surface finish may suffer.
Maintenance
Annually inspect the door or window to confirm that it operates with the correct clearances, closes and opens without obstruction and confirm that the bolt tips freely enter
the receiving aperture when the door or window is closed - adjust the door/window if necessary.
Annually check that when the door/window is closed, the lock can be locked by key and by the snib lever.
NB : The lock assembly has been lubricated for life, and should not be disassembled by the user.
Cleaning Powder Coatings
Every six months, powder coated surfaces should be cleaned to protect the finish. However, in areas where pollutants are more prevalent, especially in coastal or
industrial regions, cleaning should be carried out every two to three months.
To clean the powder coated surface:
1. Carefully remove any loose deposits with a wet sponge.
2. Use a soft brush (non abrasive) or cloth and a mild household detergent solution to remove dust, salt and other deposits. Do not use steel
wool, scrapers, scouring liquids or powders to remove deposits as these permanently scratch the coating surface.
3. Rinse off with clean fresh water.
Cleaning Chrome, Satin Chrome, Gold and Brass Finishes
Plated finishes are susceptible to tarnishing if they come into contact with moisture, wet paint, or water vapour. All plated finishes should be coated with a
non-abrasive furniture or car wax immediately after installation. Plated finishes should be regularly wiped with a non-abrasive furniture or car wax, taking care not to scratch
any protective finishes that are employed to protect the surface and prevent tarnishing.
Double Shoot-Bolt - MAINTENANCE LOG
In order to protect your warranty, record all maintenance activity in the following log:
Address of Building :
Name of Door/Window:
Date
Activity
9.
Adjust Bolt Tips
Check the position and operating
range of the bolt tips.
If necessary, the bolt tips can be
adjusted up to 5mm inward or
outward from the starting
position. This is done by
threading or unthreading
the bolt tip on the
drive tube.
NOTE: This should be
no more than 4 complete
turns in either direction.
10.
Attach Cover Plate
Fit the two black rubber interference sleeves
into the two holes on the fixing plate.
Press the cover plate onto the fixing plate.
NOTE: This step can be done after the
door/window is installed in the building to
protect the cover plate from being damaged.
fixing plate
interference sleeves
cover
plate
Signed
a Division of GAINSBOROUGH
Hardware Industries Limited
Austral Lock Pty Ltd
31-33 Alfred St, Blackburn
Victoria 3130 Australia
ph (+61 3) 9210 4193
www.ausloc.com
MADE IN AUSTRALIA BY
Austral Lock
Advertisement
