Kitsound SLAM 70 Owner's Manual

Kitsound SLAM 70 Owner's Manual

Bluetooth party speaker

Advertisement

REG05 – International – USA, EU, AUS
FRONTCOVER
KSSLA70
KitSound SLAM 70 Bluetooth Party Speaker
Owner's Manual
INNER LEAF
Please read this manual carefully before use.
WARNING
Please do not get the product wet. If your product is IP rated, please follow guidelines on
how to safely use your product overleaf.
Please don't take the product apart. There are no user serviceable parts inside
Please don't modify or alter the product or accessories
Please don't expose the product to extreme temperatures or rapid changes of hot to cold or
vice versa
Please don't use damaged cables or plugs, or loose electrical sockets
Please don't touch the device, cables, plugs, or the electrical socket with wet hands or other
wet body parts
Please don't pull the cable excessively when disconnecting it if the cable is not fixed
Please don't bend or damage the cable
Please don't drop or cause an impact to the product or the device
Please don't place naked flame sources, such as lighted candles, on the product
Battery Information
Batteries may malfunction if they are not used for extended periods
Over time, unused devices will discharge and must be recharged before use
Disconnect the charger from power sources when not in use
Use the batteries only for their intended purposes
Follow all instructions in this manual to ensure the longest lifespan of your device and battery.
Damages or poor performance caused by failure to follow warnings and instructions can void
your manufacturer's warranty
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like
QA-MRK-FM-08-02 v1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SLAM 70 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Kitsound SLAM 70

  • Page 1 REG05 – International – USA, EU, AUS FRONTCOVER KSSLA70 KitSound SLAM 70 Bluetooth Party Speaker Owner’s Manual INNER LEAF Please read this manual carefully before use. WARNING • Please do not get the product wet. If your product is IP rated, please follow guidelines on how to safely use your product overleaf.
  • Page 2 AUX/DC IN cap; exposing the speaker to liquids without doing so may result in permanent damage to the speaker. • Do not expose the Slam 70 to water while charging; this is very dangerous as doing so may result in personal injury and permanent damage to the speaker or power source.
  • Page 3 Quick Start Guide 1. Power On by pressing Power button for 2 seconds. 2. Turn on your device’s Bluetooth and connect to ‘KS Slam 70’. Change to ‘Press & hold for 2 seconds’ ^ Change up the Lighting and Boost the Sound 1.
  • Page 4 Box contents • KS SLAM 70 Bluetooth Speaker • User manual • 3.5 mm aux cable • Micro USB charge cable Functions Power Button Volume+/Next track Volume–/Previous track Pairing Button Chill Mode Button Party Mode Button Lighting / Strobe Button...
  • Page 5: Getting Started

    Slam 70 for extended periods away from mains charge capability. • When the battery is in power saving mode, the Slam 70 volume will be limited to 50%. Please recharge the battery further if you wish to increase the volume.
  • Page 6 TWS pairing two KS Slam 70 speakers 1. Press Power button (1) to turn on both of the Slam 70 speakers that you wish to pair together. Both speakers will automatically enter pairing mode. 2. Double press the Pairing Button (4) on either of the speakers and it will enter TWS pairing.
  • Page 7 Pairing button (4) flashing red. 3. Once connected, pairing button (4) will now be white on both speakers. Once connected to the Slam 70 either wired or by Bluetooth, please follow the instructions on next page: Function...
  • Page 8 TWS pairing. Light mode controls The Slam 70 has four different light modes. These include Chill mode 1, 2 and 3, as well as Party mode. Within Party mode there is the additional option to add strobe lighting.
  • Page 9: Sound Modes

    We recommend using a 2.1 amp power bank for charging your Slam 70. If you don’t own a power bank, please contact Kitsound. We will be able to recommend power banks for purchase.
  • Page 10: Specifications

    The volume in Battery Protection Mode will be limited to 50%. If your Slam 70 is out of battery it will take up to 1 hour and 20 minutes to charge up and exit Battery Protection Mode, if you are playing music at 100% volume.
  • Page 11: Back Cover

    - Consult the dealer or an experienced radio/TV technician for help The use and operation of this product is beyond our control. Warranty of the KitSound Slam 70 is limited to defects caused by faulty manufacture or defects in materials only. No warranty whatsoever is given or implied for damage caused by the user under any circumstances.
  • Page 12 All trademarks are acknowledged as the property of their respective owners. Unless otherwise stated their use does not imply that the trademark owner is affiliated with KitSound or endorses the products herein. Products showing the ‘Crossed Through’ wheelie bin symbol must be recycled separately from household waste at the end of their useful life.

Table of Contents

Save PDF