Advertisement
3.
SPEcificAtion
Collet size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6mm
Free speed: . . . . . . . . . . . . . . . . . . . . . . 22,000rpm
Air consumption:. . . . . . . . . . . . . . . . . . . . . . . . 3cfm
Operating pressure: . . . . . . . . . . . . . . . . . . . . . 90psi
Air inlet size: . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
4.
PrEPArAtion
4.1.
Air Supply
Recommended hook-up procedure is shown in fig.1.
4.1.1. Ensure die grinder air valve (or trigger) is in "off" position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3. WArninG! Ensure the air supply is clean and does not exceed 90psi while operating the die grinder.
Too high an air pressure and unclean air will shorten the product life due to excessive wear, and may be
dangerous causing damage and/or personal injury.
4.1.4. Drain the air tank daily. Water in the air line will damage the die grinder.
4.1.5. Clean air inlet filter weekly.
4.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose diameter should be 1/4" I.D. and fittings must have the same inside dimensions.
4.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all
connections are secure.
4.2.
couplings.
Vibration may cause failure if a quick change coupling is connected directly to the die grinder.
To overcome this, connect a leader hose to the grinder. A quick change coupling may then be used to
connect the leader hose to the air line recoil hose. See fig.1 & 2.
fig.1
5.
oPErAtion
5.1.
fittinG Grinding Stone
WArninG! Disconnect from the air supply before changing grinding bit.
5.1.1. Check that grinding stones are not damaged in any way such as cracks, deformations or splinters etc.
Damaged stones must not be used.
5.1.2. Use wrenches enclosed to loosen collet locking collar. Insert grinding bit and re-lock collar.
5.2.
oPErAtinG
WArninG! Ensure you have read, understood and apply safety instructions.
5.2.1. Connect the die grinder to the air supply.
5.2.2. To start, hold firmly and push the trigger locking lever forward whilst depressing trigger.
5.2.3. The bit must be running at its maximum speed before attempting to grind the workpiece.
5.2.4. Slowly and smoothly bring the grinding bit toward the workpiece (avoid jerky movements).
Exert adequate pressure on the die grinder to grind according to the type and size of the material you
are working with. Avoid subjecting bit to excessive strain or harsh impacts. Always hold die grinder
firmly and ease grinding bit against workpiece. Maintain a controlled progression.
DO NOT allow die grinder to free run for an extended period of time as this will shorten its life.
© Jack Sealey Limited
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7kg
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . 95db.A
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . 84dB.A
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . 1∙25m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . ∙061m/s²
Original Language Version
fig.2
Issue: 2(SP) - 15/07/14
SA654.V3
Advertisement
