Advertisement
1.2.
LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such
paint is toxic and must therefore be avoided. The following action must be taken before using the
sander on a surface that you suspect may contain lead paint.
1.2.1.
User must determine potential hazard relating to age of paint to be removed. (Modern paints do not
have lead content).
1.2.2.
DANGER! Keep all persons and pets away from the work area. The following are particularly
vulnerable to the effects of lead paint dust: Pregnant women, babies and children.
1.2.3.
We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Our ref SSP1604)
b) General Purpose Hooded Coveralls (Our ref SSP267L/XL).
c) Latex Gloves (Our ref SSP24).
1.2.4.
Take adequate measures to contain the paint dust, flakes and scrapings.
1.2.5.
Continue to wear safety equipment as in paragraph 1.2.3. and thoroughly clean all areas when task is
complete. Ensure paint waste is disposed of in sealed bags or containers according to local
regulations.
2. INTRODUCTION & SPECIFICATION
The SA22.V3 has a counter-balanced drive shaft for smooth operation. Palm-type trigger with rubber head rings
allows for comfortable one-handed operation.
Pad Size: . . . . . . . . . . . . . . . . . . . 170x95mm
Free Speed: . . . . . . . . . . . . . . . . . . . 8000rpm
Orbit:. . . . . . . . . . . . . . . . . . . . . . . . . . .Ø5mm
Operating Pressure: . . . . . . . . . . . . . . . .90psi
Air Consumption: . . . . . . . . . . . . . . . . . . 6cfm
3. PREPARING SANDER FOR USE
3.1.
Air Supply
Recommended hook-up is shown in fig.1.
3.1.1. Ensure the sander air valve (or throttle) is in the "Off" position before connecting to the air supply.
3.1.2. You will require an air pressure between 70-90psi, and an air flow of 5cfm.
3.1.3. WARNING! Ensure that the air supply is clean and does not exceed 90 psi while operating the
sander. Too high an air pressure and/or unclean air will shorten the product life due to excessive wear
and may be dangerous causing damage and/or personal injury.
3.1.4. Drain the air tank daily. Water in the air line will damage the sander and will invalidate your warranty.
3.1.5. Clean air inlet filter weekly.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres).
The minimum hose and fittings internal diameter should be ¼" internal diameter.
3.1.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3.2.
Couplings
Vibration may cause failure if a quick connect coupling is connected directly to the air sander. To
overcome this, connect a leader hose (Sealey Part No. AH2R) to the sander. A quick connect coupling
may then be used to connect the leader hose to the air line recoil hose. See fig.1 & fig.2.
fig. 1
©
Jack Sealey Limited
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . ¼"BSP
Sound (Power): . . . . . . . . . . . . . 102.41dB(A)
Sound (Pressure): . . . . . . . . . . . . 91.41dB(A)
Vibration Level:. . . . . . . . . . . . . . . . . 8.27m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . 0.8m/s²
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . 2kg
Original Language Version
fig. 2
SA22.V3
Issue: 5(SP) 05/01/14
Advertisement
