Advertisement
2. INTRODUCTION & SPECIFICATION
Stylish modern design heater with 2 heat settings of 750/1500W. Features
PTC heat conducting ceramic elements to achieve an instant, odour-free
heat. Full range ambient room thermostat maintains temperature at a
pre-set level. Includes overheating protection and safety tilt switch,
protecting the user, product and environment. Supplied with 13Amp
non-rewirable plug.
min. Power:............................... 750W
max. Power:............................. 1500W
Input supply:............................. 230V 13A
Dimensions (W x D x H):.......... 225 x 220 x 228mm
Weight:...................................... 1.7kg
Fig.2
Feet
Tilt safety switch
3.
CERAMIC ELEMENTS
WARNING! There are no user serviceable components inside this heater, if an element requires replacing please return to an authorised
Sealey dealer.
4. OPERATION
WARNING! Ensure you read, understand and apply the safety instructions in Section 1 before using the heater.
NOTE! The ceramic element is fragile and therefore it is important that it is not subjected to any unnecessary shocks or vibration and is not
moved when it is hot.
4.1.1
Unwrap the mains lead, place where required on its four feet and safety tilt switch and plug it into the power supply. See fig.3 for
recommended clear space in front of heater.
4.1.2
For fan only select switch position
4.1.3
Turn the thermostat control to the mid position setting. (See 4.1.9 for first time use or after storage usage)
4.1.4
Choose the required heat output by selecting the appropriate switch.
4.1.5
low setting: Select switch with the Roman numeral "I".
High setting: Select switch with the Roman numeral "II".
4.1.6
once the room reaches the set temperature the heater will switch on and off automatically to maintain that temperature. Adjust the
thermostat to obtain a comfortable room temperature. If the fan fails to operate when a power setting is selected the thermostatic
temperature control may be set too low. Slowly turn the thermostat towards maximum until the fan starts.
4.1.7
To switch the unit off, turn the heat selecting switch off "o"and unplug from the mains. Allow the unit to cool before handling or storage.
4.1.8
Safety cut-outs. The heater is fitted with a thermostatic safety cut-out which will automatically turn the heater off should it be placed in
circumstances that cause overheating or malfunction. Should this happen, switch the heater off and disconnect it from the mains. Allow
the heater to cool before handling. Do not use the heater again until the cause has been identified and remedied. If necessary return the
heater to your Sealey dealer for servicing. In the event of the heater being knocked over or raised from the ground, a safety tilt switch,
will disable the heater.
4.1.9
When used for the first time, it is suggested that you set the heater to maximum power for a few minutes in a well ventilated room to
eliminate the newness smell typical of this type of heater.
ImPoRTAnT: DURInG REloCATIon, THE HEATER SHoUlD REmAIn SWITCHED oFF AnD DISConnECTED FRom THE PoWER
SUPPlY.
In the event the heater has been accidentally knocked over, follow these steps to re-start the heater.
a)
Switch 'off' the heater at the "o" position (Fig.1).
b)
Disconnect the power cord from the power supply.
c)
Return the heater to a standing position on its four feet.
d)
If no damage has occurred to elements, re-connect power cord to the power supply and switch the heater back on. Should the power
cord require replacement, a complete wiring loom should be purchased and fitted by a suitably qualified person.
© Jack Sealey limited 2013
Fig.1
Fig.3
60° Swept area
clear of objects
Original Language Version
Fan only
off
Illuminates
when heater
operating
Thermostat
750W + Fan
1500W + Fan
CH2013
Issue: 1 - 19/04/13
Advertisement
