Advertisement
Positioning the heater
Always ensure that the heater is stood on a firm, level base near to,
but not directly beneath, a suitable mains supply socket.
Ensure that curtains and furniture are not positioned close to the chosen
position, as this would create a potential fire hazard.
We recommend that the heater should be wall-mounted in rooms where
children may be left unattended.
See also 'Important Safety Advice'
IMPORTANT – The
wall
supplied with the heater must be used.
Fig. 3
Wall Mounting
The heater should be positioned observing the minimum clearances -
see Fig. 1 and in accordance with the safety warnings.
Three identical wall mounting brackets are secured to the base of the
heater with a fixing screw. To wall mount appliance, first remove the
brackets as follows :
Lay the heater on its back.
Following the sequence in Fig. 2 – identify and remove the fixing screw
securing the brackets as shown in (a), then pull out brackets and rotate
them to disengage them from the slot (b).
Select a suitable position on a wall, near to a mains power socket,
making sure that there is at least 230 mm below the heater and at least
450 mm above the heater of unobstructed space - see also 'Positioning
the heater'.
Fix the two top retaining brackets to the wall, using suitable fixings at
358mm centres – see Fig. 3.
Locate the heater on the top brackets and allow it to hang in place.
Fit the bottom bracket into the slot in the heater and then fix it to the
wall.
Test that the heater is now securely fixed to the wall.
Operation
Plug in and switch on at the wall socket. On model's with a neon, the
neon will light when the heater is connected to the power supply.
Thermostat
The thermostat controls the heat output according to the room
temperature. This ensures that the heater will not produce heat
unnecessarily when the room is warm. To set the temperature you
require, turn the thermostat knob clockwise until the desired temperature
is reached. Alternatively to heat a cold room quickly, turn the thermostat
knob up fully. When the room has reached the desired temperature,
turn the thermostat knob anti-clockwise until the thermostat just clicks
off.
The heater will now automatically operate at this temperature.
The thermostat also has a frost protection setting marked '
setting is useful in areas such as garages to prevent frost damage. If
the thermostat is set to its minimum setting '
ON and OFF to maintain a temperature of approximately 5°C to help
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014,
EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
DIMPLEX
MILLBROOK HOUSE
GRANGE DRIVE
HEDGE END
SOUTHAMPTON
SO30 2DF
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex.
A division of GDC Group Ltd,
shelf
brackets
floor
', the heater will cycle
protect against frosty conditions.
Heat Selector Switch
The heat selection switch is an economy feature.
The switch is a 2 position switch with two possible heat settings as
follows;
I
I I
Important Notes
Although this heater is manufactured to comply with the relevant safety
standards, certain types of carpets could become discoloured by the
610mm
min.
temperatures under a portable heater. If you are concerned about this,
we recommend that you contact the carpet manufacturer for guidance.
Alternatively, either stand the heater on a suitable base to shield the
carpet or wall-mount it – call our Helpline for further advice.
You may notice some parts of the element appearing to glow hotter or
redder from time to time because of the variable airflow through the
heater. This does not cause a safety hazard.
480mm
min.
The heat outlet grille may become discoloured with use – this is caused
by airborne pollution and is not a fault.
Safety – overheat protection
switch on the heater.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not be disposed
of with household waste. Please recycle where facilities exist. Check
with your Local Authority or retailer for recycling advice in your country.
Cleaning and User Maintenance
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any kind
on the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust and
a damp cloth (not wet) to clean off stains. Be careful not to allow
moisture into the heater.
After Sales Service
Your product is guaranteed
Within this period, we undertake to repair or exchange this product
free of charge provided it has been installed and operated in accordance
with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales information or assistance with this
product please go to www.dimplex.co.uk where you will find our
self help guide by clicking on "After Sales" or ring our helpdesk on
0845 600 5111 (UK) or 01 842 4833 (R.O.I.) .
'. This
Spare parts are also available on the website
www.dimplex.co.uk
Please retain your receipt as proof of purchase.
TEL: 0845 600 5111
FAX: 01489 773050
WEBSITE: www.dimplex.co.uk
Republic of Ireland
- The heater operates at half heat output.
- The heater operates at full heat output.
For your safety, this appliance is fitted with a thermal
cut-out. In the event that the product overheats, the cut-
out switches the heater off automatically.
To bring the heater back into operation, remove the cause
of the overheating, then unplug or turn off the electrical
supply to the heater for a few minutes.
When the heater has cooled sufficiently, re-connect and
for one year
from the date of purchase.
Tel.
01 8424833
Advertisement
