Advertisement
C
/ C
ABLE
ABLE
Y
our Cable TV input into your home may be a single (75 ohm)
cable or use a cable box decoder. In either case the connec-
tion is very simple. Follow the steps below to connect your cable
signal to your new television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable Company
supplied cable to the 75Ω input on the bottom of the
TV.
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV.
The sound from the cable box will be mono.
Connect the open end of the round Cable Company sup-
1
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
2
Using a separate round coaxial cable, connect one end to the
OUT(put) (to TV) plug on the back of the Cable Box.
Connect the other end of the round coaxial cable to the
3
75Ω input on the bottom of the television.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the cable box on the
TV to the corresponding channel. Once tuned, change channels at
the cable box, not the television.
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
Connect the open end of the round Cable
1
Company supplied cable to the cable signal
IN(put) plug on the back of the Cable Box.
2
Using an RCA type Video Cable, connect one end
of the cable to the Video (yellow) (or ANT, your
cable box may belabeled differently) Out jack on
the cable box and the otherend to the Video end of
the composite adapter included with the TV.
.
3
Using an RCA type Audio Left and Right Cable,
connect oneend to the left and right Audio Out
L and R jacks (red and white) on the cable box.
Connect the other ends to the Audio end of the
composite adapter cable included with the TV.
Connect the adapter into the AV In jack on the
bottom of the TV.
NOTE: Use the Source button on the remote control to
tune to the AV1 channel for the cable box signal. Once
tuned, change channels at the cable box, not the television.
Pressing the Source button repeatedly will scroll all the
AV input channels, including the presently tuned channel.
A
NTENNA
A
combination antenna receives normal broadcast chan-
nels (VHF 2–13 and UHF 14–69). Your connection is
easy because there is only one 75Π (ohm) antenna plug on
the back of your TV, and that's where the antenna goes.
1
If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
2
Push the round end of the adapter (or antenna) onto the
75Ω (ohm) plug on the bottom of the TV. If the round end
of the antenna wire is threaded, screw it down finger tight.
H
OOKING UP THE
B
TV
OX
Cable Signal IN
from the Cable Company
1
Video Cable
(Yellow)
TV
T
ELEVISION
Cable Signal
coming from
Cable Company
(Round 75Ω
1
coaxial cable)
2
1
Round 75Ω Coaxial Cable
COMPONENT VIDEO INPUT
Pr
Pb
Y
Jack Panel at back of Cable Box with AV option
2
Antenna Connection:
Outdoor or Indoor
Antenna (Combination
1
VHF/UHF).
The combination
antenna receives
normal broadcast
Twin
channels 2-13 (VHF)
Lead
and 14-69 (UHF).
Wire
Round 75Ω
Coaxial Cable
from Antenna
3
AV3
S-
COMPONENT VIDEO INPUT
R
AUDIO
L
VIDEO
in
Pr
Pb
Y
AV1
Jack Panel at bottom of TV
Output Channel Switch
Jack Panel at bottom of TV
R
AUDIO
L
VIDEO
in
AV1
3
Audio Cables L & R
(Red / Whiite)
COMPONENT VIDEO INPUT
R
AUDIO
L
VIDEO
in
Pr
Pb
Y
AV1
300 to 75-ohm
Adapter
2
R
AUDIO
COMPONENT VIDEO INPUT
Pr
Pb
Y
AV1
Jack Panel at bottom of TV
Jack Panel at bottom of TV
L
VIDEO
in
Advertisement
