Table of Contents
Advertisement
T6460/550/552EZ(EN)_EST.qx3
6. Manual recording
General information
Use 'Manual recording' to make a spontaneous
recording (for example, a programme currently
being shown).
If you want to start and stop a recording manually,
read the section 'Recording without automatic
switch-off'.
If you want to start a recording manually but
have it stopped automatically, read the section
'Recording with automatic switch-off'. (e.g.
not to record to the end of the tape)
Recording without automatic
switch-off
1.
1.
Insert a cassette.
2.
2.
Use
to select the programme num-
P+
P–
ber you want to record, for example, 'P01'.
3.
3.
To start recording, press
4.
4.
Stop recording with
The message 'PROTECTED CASSETTE
CANNOT RECORD' appears briefly on the
screen, then the cassette is ejected.
A cassette without its security tab had been
inserted. Cover the hole with adhesive tape or
insert a new cassette.
Recording with automatic switch-off
(OTR One-Touch-Recording)
1.
1.
Insert a cassette.
2.
2.
Use
PROG P+
PROG P–
programme number you want to record.
3.
3.
Press
.
REC I
4.
4.
Each time you press
minutes to the recording time.
5.
5.
To stop recording, press
Preventing accidental erasing
All cassettes (except
rental and pre-recorded
cassettes) have a securi-
ty tab on the back of the
cassette.
To prevent recording
over important recordings
(erasing), you can remove this security tab.
If you later decide to record on a protected cas-
sette, simply cover the hole with adhesive tape
or slide the tab to the right.
04.1.28
4:15 PM
.
REC I
.
STOP C-L
or
to select the
0..9
you will add 30
REC I
.
STOP C-L
11
Page 11
Lining up recordings (assemble cut)
When you add a further recording to a cassette,
which already has a recording on it, a short blank
(flicker) can appear between the old and the new
recording or the picture itself can flicker. To help
reduce these from occurring, proceed as follows:
1.
1.
Find the tape position of the old recording
where you want to insert the new recording.
2.
2.
Look at the last minute of the old recording
(playback).
3.
3.
Press
at the tape position where the
STILL
2
2
new recording is to go and press
4.
4.
Now start recording as usual by pressing
on the remote control.
REC I
5.
5.
Stop recording with
STOP C-L
Selecting the recording speed (SP or LP)
LP allows to double the recording duration on
tape (for example six hours instead of three
hours on a E180 cassette).
1.
1.
Switch on the TV. If required, select the
programme number for the TV-Video Combi.
2.
2.
Press
. The main menu will appear.
MENU
3.
3.
Select 'RECORD SETUP' using
and confirm with
STOP C-L
4.
4.
Select 'RECORD SPEED' using
.
STOP C-L
SELECT K L CHOOSE B
RECORD SPEED
END=EXIT
5.
5.
Select the required recording speed with
.
FWD 1- B
'SP' / 'LP'
'SP': Standard Play (normal recording speed)
offers the usual first-class picture quality.
'LP': Long Play (half recording speed, double
recording time). 6 hours can be recorded on a
3-hour cassette (E180) with a somewhat
reduced picture quality.
6.
6.
To end, press
STATUS/EXIT
.
REC I
.
or
PLAY B-K
.
FWD 1- B
or
PLAY B-K
[SP]
.
EN
Advertisement
Table of Contents
