Phoenix Contact CUTFOX 10 Original Operating Instructions

Phoenix Contact CUTFOX 10 Original Operating Instructions

Advertisement

Operation of the Cutting Machine
Original operating instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CUTFOX 10 and is the answer not in the manual?

Questions and answers

Summary of Contents for Phoenix Contact CUTFOX 10

  • Page 1 Operation of the Cutting Machine CUTFOX 10 Original operating instructions...
  • Page 3 Original operating instructions Operation of the Cutting Machine CUTFOX 10 2015-05-05 Designation: UM EN CUTFOX 10 Revision: Order No.: — This user manual is valid for: Designation From this Serial No. onwards Order No. CUTFOX 10 231000 1206829 PHOENIX CONTACT...
  • Page 4 How to contact us Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be found on the Internet at: phoenixcontact.com Make sure you always use the latest documentation.
  • Page 5 The receipt of technical documentation (in particular user documentation) does not constitute any further duty on the part of Phoenix Contact to furnish information on modifications to products and/or technical documentation. You are responsible to verify the suitability and intended use of the products in your specific application, in particular with regard to observing the applicable standards and regulations.
  • Page 6: Table Of Contents

    Exiting from cutting ....................14 Troubleshooting ........................15 Error messages on the Display ................15 The length cut is wrong..................16 Adjusting the cable conveyor speed ..............16 CUTFOX 10 will not switch on ................17 Adjusting or replacing the rollers................18 Replacing the cutters ..................19 Appendix ..........................20 Ordering data.......................20 Technical data .....................20...
  • Page 7: Basic Information

    Willful modifications to the CUTFOX 10 are prohibited for safety reasons. The required length and number of wires is entered either directly in the CUTFOX 10 with the keypad or can be documented on the PC with the supplied software and loaded to the CUTFOX 10.
  • Page 8: Operating The Cutfox 10

    CUTFOX 10 Operating the CUTFOX 10 Scope of supply and overview Figure 2-1 Scope of delivery and overview of the operating components RS-232 interface 11 Metering roller Mains connection 12 Insertion slot Mains fuses 13 Door opener Mains switch 14 Display...
  • Page 9: Setting Up The Cutfox 10

    (operat- ing range: 15°C ... 35°C). NOTE: Set up the CUTFOX 10 so that it cannot slip from its work surface. Use a non-slip mat or fix the CUTFOX 10 in place, as depicted in Fig. 9 (right).
  • Page 10: Connecting And Inserting The Cable

    Connecting and inserting the cable Connecting to mains • Connect the power cable (2). • Switch on the CUTFOX 10 with the mains switch (3) (press I). The display (4) and the red "stop" LED (5) light up. Inserting the cable •...
  • Page 11: Automatic Cable Cutting

    Operating the CUTFOX 10 Automatic cable cutting The CUTFOX 10 cuts the amount entered automatically to a specified length. This is the default mode and is active when the machine is switched on. • Switch on the CUTFOX 10. •...
  • Page 12: Planning Cutting Jobs With A Pc

    Load the desired project to the CUTFOX 10 with help of the software. CUTFOX 10 While the project is being loaded to the CUTFOX 10, a display appears on the screen. When it is finished loading, a display for project selection appears.
  • Page 13 Permanent changes have to be made at the PC and then loaded to the CUTFOX 10. If, for example, a data record has been created where more cable is cut than actually re- quired, then the number can be decreased here.
  • Page 14: Manual Cable Cutting

    The cable can be moved and cut using button commands. • Insert the cable as described (see page 10). • Switch on the CUTFOX 10. • To switch into this mode, press the "mode" button and then the "3" key. Length moved (mm or inch, see page 10)
  • Page 15: Troubleshooting

    Check if the cable cross section is too large or if the ca- ble is for some other reason not suitable. • Switch the cutter (see page 19). Press the "enter" key to delete the error message. Metering and drive rollers Drive rollers Metering roller 102786_en_03 PHOENIX CONTACT...
  • Page 16: The Length Cut Is Wrong

    If the insulation of the cable is very hard, the metering roller can be exchanged with a PU roller or a steel roller (see page 18). If the actual length cut is not consistent with the length set, the CUTFOX 10 has to be read- justed.
  • Page 17: Cutfox 10 Will Not Switch On

    CUTFOX 10 will not switch on No mains connection • Check whether the mains plug is connected to the CUTFOX 10 mains connection and the shock-proof plug is connected to the mains socket. • Make sure that the power supply at the mains socket is OK.
  • Page 18: Adjusting Or Replacing The Rollers

    Rotate left  more pressure Rotate right  less pressure Replacing drive or metering rollers WARNING: Risk of injury Switch off the CUTFOX 10 and disconnect the mains plug. • Press the door opener and fold down the front door.
  • Page 19: Replacing The Cutters

    Troubleshooting Replacing the cutters Removing the drive rollers WARNING: Risk of injury Switch off the CUTFOX 10 and disconnect the mains plug. • Press the door opener and fold down the front door. • Insert the removal hook (1) supplied behind the rollers (2) and push off the rollers.
  • Page 20: A Appendix

    Drive / metering rollers 2 replacement rolls for CUTFOX 10 CF-10 WHEEL SET 1207271 2 replacement rolls for CUTFOX 10, with PU CF-10 WHEEL PU 1200098 tread, for sensitive cables/conductors and their in- sulation (for hard insulation to some extent)
  • Page 21: Declaration Of Conformity

    Declaration of conformity Declaration of conformity PHOENIX CONTACT GmbH & Co. KG, Flachsmarktstraße 8, D-32825 Blomberg, Ger- many CUTFOX 10 1206829 CUTFOX 10 BASIC 1207543 The above-mentioned products are in conformity with essential requirements of the follow- ing directives and their amending directives.
  • Page 22 CUTFOX 10 PHOENIX CONTACT 102786_en_03...

Table of Contents