Advertisement
C
/C
ABLE
ABLE
Y
our Cable TV input into your home may be a single (75 ohm)
cable or use a cable box decoder. In either case the connec-
tion is very simple.
Follow the steps below to connect your cable signal to your new
television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable Company sup-
plied cable to the 75Ω input on the TV. Screw it down finger
tight.
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV. The sound
from the cable box will be mono.
2
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
3
Using a separate round coaxial cable, connect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
4
Connect the other end of the round coaxial cable to the
75Ω input on the back of the television. Screw it down finger
tight.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the cable box on the
TV to the corresponding channel. Once tuned, change channels at
the cable box, not the television.
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
5
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
6
Using a RCA type Video Cable, connect one end of the
cable to the Video (or ANT, your cable box may be labeled
differently) Out jack on the cable box and the other end to the
AV1 Video Input on the TV.
7
Using a RCA type Audio Left and Right Cable, connect one
end to the left and right Audio Out L & R jacks on the
cable box. Connect the other end to the AV1 Audio L & R
Input jacks on the TV.
NOTE: Use the Channel +, or – buttons on the TV remote control to
tune to the AV1 channel for the cable box signal. Once tuned, change
channels at the cable box, not the television.
A
NTENNA
A
combination antenna receives normal broadcast chan-
nels (VHF 2–13 and UHF 14–69). Your connection is
easy because there is only one 75Ω (ohm) antenna plug on
the back of your TV, and that's where the antenna goes.
1
If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
2
Push the round end of the adapter (or antenna) onto the
75Ω (ohm) plug on the back of the TV. If the round end of
the antenna wire is threaded, screw it down finger tight.
H
OOKING UP THE
B
TV
Direct Cable Connection:
OX
Cable Box with RF Inputs and Outputs Connection:
Cable Signal
IN from the
Cable
Company
Cable Box with Audio/Video Outputs Connection:
Cable Signal IN
from the Cable
TV
Antenna Connection:
Cable signal
coming from
1
Cable Company
(Round 75Ω
coaxial cable)
2
CABLE
IN
Round 75Ω
Coaxial Cable
Company
5
OUTPUT
CH
3
4
CABLE
TO
VIDEO
IN
TV
OUT
Video Cable (Yellow)
6
Monitor out
AV1 in
VIDEO
Y
L/Mono
Pb
AUDIO
R
Pr
COMPONENT VIDEO INPUT
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The combination antenna receives normal
broadcast channels 2-13 (VHF) and 14-69 (UHF).
1
300 to 75-ohm
Twin
Lead Wire
Round 75Ω Coaxial
Cable from Antenna
2
TV
ANT 75‰
Monitor out
AV1 in
AV2 in
VIDEO
L/Mono
Y
Pb
AUDIO
S-VIDEO
R
Pr
COMPONENT VIDEO INPUT
Jack Panel Back of TV
Output Channel Switch
3
OUTPUT
CH
3
4
TO TV
4
Jack Panel Back of TV
Jack Panel Back
of Cable Box with A/V Outputs
L
R
AUDIO
OUT
Audio Cables
L & R (Red, White)
AV2 in
S-VIDEO
Jack Panel Back of TV
7
Adapter
2
Jack Panel Back of TV
Jack Panel Back
of Cable Box
ANT 75‰
Monitor out
AV1 in
AV2 in
VIDEO
Y
L/Mono
AUDIO
Pb
S-VIDEO
R
Pr
COMPONENT VIDEO INPUT
24
ANT 75‰
Monitor out
AV1 in
AV2 in
VIDEO
L/Mono
Y
Pb
AUDIO
S-VIDEO
R
Pr
COMPONENT VIDEO INPUT
ANT 75‰
Monitor out
AV1 in
AV2 in
VIDEO
L/Mono
Y
AUDIO
Pb
S-VIDEO
R
Pr
COMPONENT VIDEO INPUT
Advertisement
