Valu-air SF5040E Instruction Manual
  1. Manuals
  2. Brands
  3. Valu-air Manuals
  4. Nail Gun
  5. SF5040E
  6. Instruction manual

Valu-air SF5040E Instruction Manual

Air-powered 2 in 1 combi nailer/stapler
Hide thumbs Also See for SF5040E:

Advertisement

Table of Contents

AIR-POWERED 2 IN 1 COMBI
Residual Risks
Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.
The following hazards may arise in connection with the tool's construction and design:
NAILER/STAPLER
MODEL SF5040E
INSTRUCTION MANUAL
IMPORTANT:
Read all safety rules and operating Instructions
carefully before starting the product.
Keep this Manual for future reference.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SF5040E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Valu-air SF5040E

Summary of Contents for Valu-air SF5040E

  • Page 1 AIR-POWERED 2 IN 1 COMBI NAILER/STAPLER MODEL SF5040E INSTRUCTION MANUAL IMPORTANT: Read all safety rules and operating Instructions carefully before starting the product. Keep this Manual for future reference. Residual Risks Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.

  • Page 2: Table Of Contents

    TABLE OF CONTENTS:  TECHNICAL SPECIFIACTIONS  SAFETY GUIDELINES  UNPACKING  KEY PARTS DIAGRAM  IMPORTANT INFORMATION  TYPES OF FASTENERS  OPERATING INSTRUCTIONS  MAINTENANCE  TROUBLESHOOTING  EXPLODED VIEW  PARTS LIST  TECHNICAL SPECIFIACTIONS: Magazine capacity(QTY.) 100pcs Drives18Ga Brad Nails 5/8”~2”...

  • Page 3: Safety Guidelines

     SAFETY GUIDELINES This manual contains information that relates to protecting personal safety and preventing equipment problems.it is very important to read this manual carefully and understand it thoroughly before using the product.the symbols listed below are used to indicate this information DANGER! Potential hazard that will result in serious injury or loss of life.
  • Page 4 -Locate the compressor in a well-ventilated area for cooling, and must be a minimum of 12”(31cm) away from the nearest wall. -Protect the air hose and the power cord from damage and puncture. Inspect them for weak or worn spots every week, and replace them if necessary .

  • Page 5: Unpacking

    When you are completely satisfied with the condition of the shipment, you should inventory the equipment. -After you open the nailer/stapler box, you should find the following. Model SF5040E Inventory (Figure 1) A. 2-in-1 Nailer /Stapler......1 B.

  • Page 6: Types Of Fasteners

     Verify that all of the connections in the air supply system are sealed in order to prevent air from leaking. Description Description Description VALU-AIR Air powered 2 in 1 nailer Air Hose Filter Quick connector Lubricator Cut-off valve Quick coupler Regulator(0 to 8.3 Bar)

  • Page 7: Operating Instructions

     OPERATING INSTRUCTIONS  To load your nailer/stapler: 1. DISCONNECT NAILER /STAPLERFROM THE AIR SUPPLY! 2. Grip the nailer/stapler firmly, unlatch the catch lever (Figure 3), and pull the magazine pusher back completely. Figure 3. Catch lever engaged and magazine pusher retracted. 3.
  • Page 8  Operating If you have not read the safety instructions in this manual, do not operate the nailer/stapler. Before you operate your nailer/stapler, place two to three drops of the included oil into the quick connect fitting where the nailer/stapler connects to the air supply. To operate your nailer/stapler: 1.
  • Page 9  Single Fire Operation SINGLE SEQUENTIAL MODE The tool is specially designed for single sequential mode. This mode requires the trigger to be pulled each time a fastener is driven. The tool can be actuated by depressing the work contact element against the work surface followed by pulling the trigger The trigger must be released to reset the tool before another fastener can be driven.

  • Page 10: Maintenance

     Replacing Pistons/O-Rings If you use your nailer/stapler day in and day out, repair pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. A replacement piston and O-ring kit, you can contact with where you buy! To replace a piston and O-ring: 1.

  • Page 11: Troubleshooting

    Lubricating  -Place 2 to 6 drops of pneumatic tool oil in the nailer air inlet (as shown in Figure 8) every 2 hours of continuous use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up. -Another option to manual oiling would be to simply install a lubricator in your air compressor line.
  • Page 12  Explode Drawing &Spare parts list Issue Date:2018.05.24 Version No:C/0 Description Description Description Description Bolt O-ring 1.7×2 spring washer 4 Srew M4×6 Elastic spacer(Quick Deflector Spring Step Pin Bolt M4×6 unloading) Cover plate(Quick Air Deflector Slide Stand fixed seat unloading) Sticker Plate(Quick Bolt M5×20 Compressed Spring...

Table of Contents

Save PDF