1. Manuals
  2. Brands
  3. Huvema Manuals
  4. Lathe
  5. MIP 30
  6. User manual

Huvema MIP 30 User Manual

Section roller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Section roller
MIP 30
Users manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MIP 30 and is the answer not in the manual?

Questions and answers

Related Manuals for Huvema MIP 30

Summary of Contents for Huvema MIP 30

  • Page 1 Section roller MIP 30 Users manual...

  • Page 2: Table Of Contents

    Contents GENERAL SAFETY RULES...........................2 ADDITIONAL SAFETY RULES ........................3 1. FEATURES..............................4 2. USE RANGE...............................4 3. TECHNICAL CHARACTERISTICS ......................6 4. OPERATION...............................6 5. LABOUR PROTECTION RULES........................6 6. MAINTENANCE............................6 7. DRAWINGS ..............................7 7.1 P ................................12 ART LIST 8. DIRECTIONS FOR OPERATION, USE AND MAINTENANCE OF ELECTRIC INSTALLATION ....13 8.1 T ............................

  • Page 3: General Safety Rules

    NB.: Read the instructions carefully in order to avoid any problems. As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine with respect and caution will considerably lessen the possibility op personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may occur.

  • Page 4: Additional Safety Rules

    Never leave the machine running unattended. © 2005, Huberts bv, Kennedylaan 14, Veghel, the Netherlands. Internet: www.huvema.nl All rights reserved. No part of this booklet may be reproduced in any form, by print, photoprint, microfilm or any other means without written...

  • Page 5: Features

    2. Use range The MIP 30 Profile roller is used for bending steel profiles got by rolling. The machine is equipped with a set of standard rollers used for bending profiles of parallelepiped section. For other type of profiles there are special sets of rollers available.
  • Page 6 MIP 30-15-5-4 Flange Ø148x13 MIP 30-15-3-2 Leading roll 50 MIP 30-15-1-8 Leading roll 45 MIP 30-15-1-9 Leading roll 40 MIP 30-15-1-10 1 Leading roll 35 MIP 30-15-1-11 1 Leading roll 30 MIP 30-15-1-12 1 Leading roll 25 MIP 30-15-1-13 1 T-profile...

  • Page 7: Technical Characteristics

    8. Round profile 30 < D ≤ 60 MIP 30-15-11-0 Guide roll 60 MIP 30-15-11-1 Guide roll 55 MIP 30-15-11-2 Guide roll 50 MIP 30-15-11-3 Guide roll 45 MIP 30-15-11-4 Guide roll 40 MIP 30-15-11-5 Guide roll 35 MIP 30-15-11-6...

  • Page 8: Drawings

    7. Drawings...
  • Page 11 -10-...
  • Page 12 -11-...

  • Page 13: Part List

    7.1 Part list Description Description Base Worm shaft Door Bearing cover Door handle Axle flange Ball lock Worm gear axle Lock key Valve Bending equipment Screw M6x14 Vertical support plate Screw M816 Connecting Screw M6x20 Guard bolt Check washer MN6 Threaded rod Sleeve A30x40x7 Main Shaft...

  • Page 14: Directions For Operation, Use And Maintenance Of Electric Installation

    8. Directions for operation, use and maintenance of electric installation 8.1 Technical conditions Supply with electrical power is made according to EN 60204-1, §4.3. The machine is wired up to a three-phase supply network: 3-50Hz; 400V; equipped with working null (N) and earthling (PE).

  • Page 15: Operation Of The Electric Equipment

    Check condition of electric instruments, junction wires, cables and electrical connections. After everything has been checked, connect the machine to the mains: Supply is made respecting all conditions in §1. In order to protect the feed circuit it is recommended to equip the power unit with fusible:3 x 10A for the 3 phases (L1, L2, L3);...

  • Page 16: Maintenance

    • If M motor is not correctly fed from 3-50Hz; 400V voltage, check motor force circuit: Check the F1 fuse in the motor force circuit. In case one of the fuses is broken, make the necessary repairs and replace the fuse. ATTENTION!! Use only calibrated replacing pieces with the parameters indicated.

  • Page 17: Electrical Wiring

    8.7 Electrical wiring Manufacturer and importer assume no responsibility for defects which result from not reading the manual carefully or wrong use of the machine. All rights reserved. Subject to change © copyright October 2005 -16-...

Table of Contents