Related Manuals for Feig Electronic ID ISC.ANT1300/680 Type A
Summary of Contents for Feig Electronic ID ISC.ANT1300/680 Type A
- Page 1 INSTALLATION ID ISC.ANT1300/680 Type A and Type B Version: Reader ID ISC.LRM2000-C, manual tuning board English final public (B) 2011-08-17 M71104-6e-ID-B.doc...
- Page 2 FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed with components and testing methods for a level of reliability suitable for use in or in connection with surgical implants or as critical components in any life support systems whose failure to perform can reasonably be expected to cause significant injury to a human.
-
Page 3: Table Of Contents
Tuning the Gate Antenna with Power Splitter ............26 Testing the Gate Antenna..................28 4.3.1 Checking the Noise Level ..................28 4.3.2 Reading a Serial Number ..................29 4.3.3 Testing the performance ..................30 Connecting and Setting the Indicators..............32 FEIG ELECTRONIC GmbH Page 3 of 45 M71104-6e-ID-B.doc... - Page 4 Approval ........................42 5.2.1 Europe (CE) ......................42 5.2.2 USA (FCC) and Canada (IC) .................. 43 Annex A Terminal assignment “Terminal Board” ..............44 Sources of supply measuring instruments and accessories ........ 45 FEIG ELECTRONIC GmbH Page 4 of 45 M71104-6e-ID-B.doc...
-
Page 5: Safety Instructions / Warning - Read Before Start-Up
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in an immediate proximity of the reader’s antennas for any length of time. FEIG ELECTRONIC GmbH Page 5 of 45 M71104-6e-ID-B.doc... -
Page 6: Performance Features Of The Id Isc.ant1300/680 Antennas
Antenna with manual tuning board ID ISC.MAT and Alarm LED ID ISC.ANT1300/680-B Antenna with manual tuning board ID ISC.MAT ID ISC.ANT1300680-SIG Light signal with mounting material Table 1: Available Antenna Types and accessories FEIG ELECTRONIC GmbH Page 6 of 45 M71104-6e-ID-B.doc... -
Page 7: Installation And Wiring
3.1 Dimensions of antenna The outside dimensions of the antenna are shown in Fig. 1 Fig. 1: Antenna outside dimensions All dimensions are in mm with general tolerance to ISO 2768 m (mean). FEIG ELECTRONIC GmbH Page 7 of 45 M71104-6e-ID-B.doc... -
Page 8: Mounting Preparation
2. After that the antenna has to be placed carefully again on the floor. Now you must remove the two fastening screws (hexagon socket width A/F2,5) of the antenna base cover and remove it upwards. Fig. 3 Step 1 Step 2 Fig. 3: Opening the antenna base FEIG ELECTRONIC GmbH Page 8 of 45 M71104-6e-ID-B.doc... -
Page 9: Installing The Antenna
The dimensions are shown in Fig. 4: Fig. 4: Floor plate dimensions All dimensions are in mm with general tolerance to ISO 2768 m (middle). FEIG ELECTRONIC GmbH Page 9 of 45 M71104-6e-ID-B.doc... - Page 10 Reader side. Alternatively the cables can be routed at the sides of the antenna bas like shown in Fig. 5 Fig. 5 Cable routing at the antenna sides FEIG ELECTRONIC GmbH Page 10 of 45 M71104-6e-ID-B.doc...
-
Page 11: Installing The Antenna Base And Antenna Body
Adjusting screws (hexagon socket width A/F5) Fig. 6: Attaching and aligning the antenna 3.3.3 Connection of components To built a gate configuration, you use one antenna Type A and one antenna Type B or BL. FEIG ELECTRONIC GmbH Page 11 of 45 M71104-6e-ID-B.doc... -
Page 12: Typical Antenna Configuration (Gate Antenna With Two Antennas)
Note that the entire capture area of the antenna is larger than the three-dimensional area shown in the drawing (Fig. 8). This means there are tag orientations in which the tag can be detected outside the capture area. FEIG ELECTRONIC GmbH Page 12 of 45 M71104-6e-ID-B.doc... - Page 13 The antenna should be at least 50 cm from metal parts. The minimum distance between the antennas of a gate and antennas of RFID work station or terminals (transmitting frequency 13,56 MHz) should be: FEIG ELECTRONIC GmbH Page 13 of 45 M71104-6e-ID-B.doc...
- Page 14 Gate distance GD Number of tags at traverse speed 1 m/s Read serial number Read data Table 4: Design notes A minimum distance of 65cm between the two gate antennas is required. FEIG ELECTRONIC GmbH Page 14 of 45 M71104-6e-ID-B.doc...
-
Page 15: Gate Configuration And Setup Using Antennas Type -A And Type -B/-Bl
Microsoft Windows and for tuning the antennas a suitable measuring device (e.g. SWR-Meter) The service can be downloaded at the Download Area of the Homepage www.feig.de. FEIG ELECTRONIC GmbH Page 15 of 45 M71104-6e-ID-B.doc... -
Page 16: Configuration Of A Gate Antenna With Power Splitter
Type BL (optional) Fig. 9: Connecting the components for a gate consisting of two antennas, reader and power splitter Fig. 10:Terminal board An overview of the terminal board assignment is given in 6.Annex A FEIG ELECTRONIC GmbH Page 16 of 45 M71104-6e-ID-B.doc... - Page 17 AL should preferably be connected shortly. Unused cable lengths are possible should be tied in antenna B/BL type. Fig. 11 Connection of the components in an antenna Type A Fig. 12 Unused coaxial cables are tied in antenna Type B/BL FEIG ELECTRONIC GmbH Page 17 of 45 M71104-6e-ID-B.doc...
-
Page 18: Setting The Power Splitter
Power Splitter with 90° phase shifter X1: Reader X2: Antenna X3: Antenna X4: 12-24V DC for Antenna with dyn. antenna tuner ID ISC.DAT Fig. 13 Jumper Settings for Power Splitter FEIG ELECTRONIC GmbH Page 18 of 45 M71104-6e-ID-B.doc... -
Page 19: Setting The Antenna Tuner
Now remove the to fastening screws (hexagon socket width A/F2,5) of the antenna tuner cover and move it downwards. Fig. 15 Step 3 Step 4 Fig. 15 Removing the antenna tuner cover FEIG ELECTRONIC GmbH Page 19 of 45 M71104-6e-ID-B.doc... - Page 20 Fig. 16 Jumper Settings for Tuning Board MAT Verify these settings with a suitable measuring device (e.g. SWR-Meter) after installing the antennas. More on setting the ID ISC.MAT antenna tuner can be found in the corresponding installation manual (M70101-xe-ID-B). FEIG ELECTRONIC GmbH Page 20 of 45 M71104-6e-ID-B.doc...
-
Page 21: Interface Connections
Fig. 17: Wiring example for connecting the RS232 interface Note: If there is an USB/RS232 converter used on the PC/Notebook side, we recommend to in- crease the „Char Timeout Multiplier“ parameter in the COM-Port settings from „1“ to about „5“. FEIG ELECTRONIC GmbH Page 21 of 45 M71104-6e-ID-B.doc... -
Page 22: Lan / Tcp/Ip
With structured cabling Cat 5 cables should be used. This ensure reliable operation at 10Mbps or 100Mbps. ACC-Modul ANT1 The default IP address is: 192.168.10.10 Port 10001 Sub Net Mask 255.255.0.0 More Information about the interfaces you will find in the manual M51001-xde-ID-B of the reader. FEIG ELECTRONIC GmbH Page 22 of 45 M71104-6e-ID-B.doc... -
Page 23: Reader Configuration With Power Splitter
„Exit“ Note: This has to be done at each start of ISO-Start program otherwise the configuration of the reader will be changed by the wizard. Select „Options => Program“ FEIG ELECTRONIC GmbH Page 23 of 45 M71104-6e-ID-B.doc... - Page 24 ® OBID i-scan Installation ID ISC.ANT1300/680-A/-B Step Action Note Select „Expert Mode“ and confirm with OK. Select “Logical View” FEIG ELECTRONIC GmbH Page 24 of 45 M71104-6e-ID-B.doc...
- Page 25 4.6 Configuring the Reader in accordance with national RF regulations Set by clicking on „Apply“. Operating Mode: For antenna tuning the reader has to be set to „Host Mode“. Set by clicking on „Apply“. FEIG ELECTRONIC GmbH Page 25 of 45 M71104-6e-ID-B.doc...
-
Page 26: Tuning The Gate Antenna With Power Splitter
C1.The standing-wave ratio should be at least 1:1,2 or better. .50 +/-5 Ohm Phase 0° +/-5° at the SWR-Analyzer. This hast o be done for both antennas. Long Range Reader ID ISC.LRM2000-C X9, Pin1+3 30cm 3,60m 1,35m Power Splitter ID ISC.ANT.PSM-B Fig. 18 Tuning the antennas with a SWR-Meter FEIG ELECTRONIC GmbH Page 26 of 45 M71104-6e-ID-B.doc... - Page 27 X9, Pin1+3 3,60m 1,35m Power Splitter ID ISC.ANT.PSM-B Fig. 19 Tuning the antennas with a SWR- Analyzer For recommended devices and possible vendors see: 6.2 Sources of supply measuring instruments and accessories FEIG ELECTRONIC GmbH Page 27 of 45 M71104-6e-ID-B.doc...
-
Page 28: Testing The Gate Antenna
Are there devices nearby which may emit noise interferences (larger machines or wireless devices)? Are there interferences from the mains? To determine which devices may be disturbing the gate, briefly disconnect them from the mains. FEIG ELECTRONIC GmbH Page 28 of 45 M71104-6e-ID-B.doc... -
Page 29: Reading A Serial Number
Measurement“ Select „ISO Inventory“ function and activate by clicking on „Start“. The serial number and tag type will be shown in the display. Repeat Step 1 to 3 for the opposite antenna FEIG ELECTRONIC GmbH Page 29 of 45 M71104-6e-ID-B.doc... -
Page 30: Testing The Performance
Then repeat this along the line in the vertical tag direction transverse to the antenna and on the line in the horizontal tag orientation. Here again the tag should always be read. FEIG ELECTRONIC GmbH Page 30 of 45 M71104-6e-ID-B.doc... - Page 31 Transponder too insensitive, detuned or defective Reader improperly configured (transmitting power, transponder type, modulation, transponder parameters, etc.). A cable is defective or has a poor contact. Reader, Power Splitter or antenna defective. FEIG ELECTRONIC GmbH Page 31 of 45 M71104-6e-ID-B.doc...
-
Page 32: Connecting And Setting The Indicators
The relay outputs are intended only for switching resistive loads. If an inductive load is used, the relay contacts must be protected by an external protection circuit. Reversing the polarity or overloading the outputs will destroy them. See also Installation Manual M51001-2de-ID-B.pdf ID ISC.LRM2000-A/B FEIG ELECTRONIC GmbH Page 32 of 45 M71104-6e-ID-B.doc... -
Page 33: Reader Setting For Indicator
AFI byte, you have to configure the reader as follow: ISO-15693 – Selection Mask Set “Enable AFI” Set the value for the AFI in field “AFI1” (e.g. 01) FEIG ELECTRONIC GmbH Page 33 of 45 M71104-6e-ID-B.doc... - Page 34 Up to four different AFI values could be set. Operating Mode If the alarm should occur by an EAS, you have to configure the reader as follow: Set “EAS” Set by clicking on „Apply“ FEIG ELECTRONIC GmbH Page 34 of 45 M71104-6e-ID-B.doc...
-
Page 35: Programming A Transponder With The Afi Byte
Transponder Select „[0x27] Write AFI“ ADR: 1: addressed Serial Number: Select Transponder UID AFI: Desired AFI Number (not equal to 00) Write AFI byte on to the transponder by click on „Send“ FEIG ELECTRONIC GmbH Page 35 of 45 M71104-6e-ID-B.doc... -
Page 36: Activating The Automatic Mode
The configuration of the Notification or Scan Mode are similar (See System Manual of the reader) To test the function of the Gate in the Buffered Read Mode, the BRM Window of ISOStart or the BRMDemo program can be used. FEIG ELECTRONIC GmbH Page 36 of 45 M71104-6e-ID-B.doc... -
Page 37: Configuring The Reader In Accordance With National Rf Regulations
When placing the antennas in service, the systems integrator must ensure that the prescribed mounting instructions are followed, the necessary Reader settings are made and permissible limits according to the national regulations are not exceeded. FEIG ELECTRONIC GmbH Page 37 of 45 M71104-6e-ID-B.doc... - Page 38 RF Modulation: Transponder RF Modulation / ISO-MODE / RF Data coding ISO-MODE: Fast (1/4) Timeslots ISO-MODE / NO-TS 1 or 16 Timeslots ISO Option – BREAK: Complete Timeslot length at „NO TAG“ FEIG ELECTRONIC GmbH Page 38 of 45 M71104-6e-ID-B.doc...
-
Page 39: Technical Data
Noise Ripple : max. 150 mV Power Consumption max. 32 VA Operating Frequency 13,56 MHz Transmit Power 2 W to 5 W (250 mW Step - Software) Maximum transmitting power per antenna FEIG ELECTRONIC GmbH Page 39 of 45 M71104-6e-ID-B.doc... - Page 40 120 cm** – All tag orientations approx. 90 cm*** Antenna connection 1 x SMA plug (50 ) Antenna connector cable RG58, 50 , approx. 2 m long Type B FEIG ELECTRONIC GmbH Page 40 of 45 M71104-6e-ID-B.doc...
- Page 41 =60 mA/m rms, transmitting power 5 W, aligned in all 3 dimensions for horizontal movement through the antenna. The detection performance also depending of the strength of the Transponder answer signal ! FEIG ELECTRONIC GmbH Page 41 of 45 M71104-6e-ID-B.doc...
-
Page 42: Approval
Equipment Classification according to ETSI EN 300 330 and ETSI EN 301 489: Class 2 The technical data of the ID ISC.LRM2000 Reader built into the ID ISC.ANT1300/680-A an- tenna can be found in the Installation Manual which is included with the device. FEIG ELECTRONIC GmbH Page 42 of 45 M71104-6e-ID-B.doc... -
Page 43: Usa (Fcc) And Canada (Ic)
OBID i-scan Installation ID ISC.ANT1300/680-A/-B 5.2.2 USA (FCC) and Canada (IC) Product name: ID ISC.ANT1300/680 Antenna name: ID ISC.ANT1300/680 Type A Reader name: ID ISC.LRM2000 FCC ID: PJMANT1300680 6633A-ANT130068 This device complies with Part 15 of the FCC Rules and with... -
Page 44: Annex A
X12 / Pin 2 GND LED2 X14 / LED3 Connection LED / Alarm LED 3. Antenna X14 / Pin 1 +24V DC LED3 X14 / Pin 2 GND LED3 Table 8: Pin-Configuration X1-X14 Terminal Board FEIG ELECTRONIC GmbH Page 44 of 45 M71104-6e-ID-B.doc... -
Page 45: Sources Of Supply Measuring Instruments And Accessories
2. Adapter : SMA/PL, 50 Ohm dummy load, koaxiale cable with connector Supplier: WiMo Antennen und Zubehör : Tel.: + 49 7276-96680, www.wimo.de Conrad Electroinc : www.conrad.de Farnell GmbH www.farnell.com FEIG ELECTRONIC GmbH Page 45 of 45 M71104-6e-ID-B.doc...