Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
·
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
·
These instructions contain important care, cleaning,
and warranty information-
instructions for the consumer.
·
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
·
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
·
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut, drilled or knocked
by hard object. Make sure corner area of the
glass refraining from knocking so as to cause
personal injury due to broken glass.
ATTENTION:
Please install this door on Kohler
receptors or curbs. (Not included). If the curb is not
Kohler-branded, please note its top width should be
more than 80mm.
IMPORTANT:
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
1198141-T01-B
please leave these
·
·
·
·
·
·
)
13-1
-1-
MINIMA
INSTALLATION INSTRUCTIONS
SLIDING, 1 DOOR 1 PANEL
8mm K-45803T-L-SHP
10mm K-45806T-L-SHP
2
80mm
3mm/m
528437
Copyright Kohler China Ltd., 2014
(
, 2014
Advertisement
Related Manuals for Kohler MINIMA K-45803T-L-SHP
Summary of Contents for Kohler MINIMA K-45803T-L-SHP
- Page 1 · · All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. · ·...
-
Page 2: Parts Identification
ROUGHING-IN Unit: mm K-45803T 1200-1600 1850-2000 K-45806T PARTS IDENTIFICATION PARTS IDENTIFICATION IMPORTANT Before installation check that all components are correctly supplied. If any parts are missing please ring the helpline. 800-820-2628 800-820-2628 Top Lintel Door Panel Inline Panel Wall Channel Glass Clamp Threshold Splashguard... - Page 3 Top Roller Clamps Mid-support Clamp 4mm Allen key 2.5mm Allen Key 2.5mm End Socket Screw Covers Bottom Guide Door Closing Guide Plastic Guides Screw Covers Support Strip Frame Cap,LH Frame Cap,RH Wall Plugs Wedge Handle 1198141-T01-B...
-
Page 4: Installation Requirements
INSTALLATION REQUIREMENTS INSTALLATION REQUIREMENTS Tools Required · · Phillips Screwdriver · · Pencil · · Caulk Gun · · Measuring Tape · · Safety Glasses · · Center Punch · · Hammer · · Knife · · Masonry Drill & 6mm Drilll Bit ·... - Page 5 Glass needs to be at least 8mm into wall channel Caution 8mm minimum Rest panel against seal of wall channel 'A' . Support glass panel until glass clamp is fitted Check that bottom channel is parallel to Bottom channel fits under edge of tray.
- Page 6 Cut seals exposed at top with a sharp knife. STEP STEP Mark hole position, remove temporarily the bottom Lay a bead of sealant in bottom guide as shown, then guide and drill hole into the tray. slide it under glass. STEP Top view Locate one end of threshold under the bottom guide.
- Page 7 Keep threshold position parallel to tray edge. Remove cover vinyl. Lay sealant on bottom of door closing guide. Place door closing guide under wall channel. STEP STEP Fit the second wall channel. Push cover vinyl Into place. Wall channel MUST plumb.
- Page 8 Screw bottom guide to tray. Top view STEP Position support clamps and sockets on top lintel. Fully tighten mid support clamp '2' & loosely fit end sockets '1' & '3'. Screw mid support clamp to Turn with allen key to lightly Turn with allen key to lintel.
- Page 9 Screw into wall channel. Place mid support clamp. Screw mid support clamp firmly to glass. STEP STEP Screw 2nd socket to wall Carefully turn door channel then tighten the allen panel on its edge screws on both sides. and support. 10mm Allen screw Fit splashguard to...
- Page 10 Fit door panel. Caution Place support spacer. Place support strip. Lower the door panel into bottom guide and rest on spacer support and strip. STEP Fit rollers clamps to top lintel and door panel. Lift door panel slightly and remove Front support strip.
- Page 11 Fit plastic guides into bottom guide. Carefully apply silicone sealant along the back face to fix the plastic guide in place. STEP Fit seals on: Closing edge Notched seal Back edge Door Door Inline panel panel panel STEP 1198141-T01-B -11-...
- Page 12 Fix cap. Fix handle. STEP STEP Allow at least 24 hours before using shower to allow Lay a thin bead of sealant. sealant to cure. 24hrs STEP STEP 1198141-T01-B -12-...