Adding Channels To The Tv's Memory; Programming Channels Automatically; Adding And Erasing Channels Manually - Toshiba 34HF81 Owner's Manual

Adding channels to the TV's memory

When you press Channel y or z, your TV will stop only on the
channels stored in the TV's channel memory.
Follow the steps below and on the next page to program all active
channels into the TV's memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and
store them in its memory. After the channels are stored automatically,
you can manually add or erase individual channels (see page 25).
To program channels automatically:
1. Press MENU, and then press x or • until the SET UP menu
appears.
2. Press y or z until the TV/CABLE is highlighted.
3. Press x or • to highlight either TV or CABLE, depending on
which you use. If you use an antenna, highlight TV; if you use
cable, highlight CABLE.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2
3
4
5
6
SET UP
7
8
LANGUAGE
9
CLOCK SET
10
ANT 1 / 2
11
TV / CABLE
12
CH PROGRAM
13
ADD / ERASE
14
T I LT CORRECT I ON
15
16
17
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
4. Press z to select CH PROGRAM.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
1
2
3
4
5
6
SET UP
7
8
9 LANGUAGE
CLOCK SET
10
ANT 1 / 2
11
TV / CABLE
12
CH PROGRAM
13
ADD / ERASE
14
T I LT CORRECT I ON
15
16
17
18
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
5. Press x or • to start channel programming. The TV will
automatically cycle through all the TV or Cable channels
(depending on which you selected), and store all active channels
in the channel memory.
While the TV is cycling through the channels, the message
"Programming Now—Please Wait" appears.
6. When channel programming is complete,the message
"Completed" appears.
7. Press Channel y or z to view the programmed channels.

Adding and erasing channels manually

After you have programmed the channels automatically, you can
manually add or erase specific channels.
To add or erase channels:
1. Select the channel you want to add or erase. If you are adding a
channel, you must select the channel using the Channel Number
buttons.
2. Press MENU, and then press x or • until the SET UP menu
appears.
24
1
2
3
4
5
6
7
8
ENGL SH I
9
0 0 : 0 0
10
ANT 1
11
TV / CABLE
12
13
ADD
14
0
15
16
17
18
1
2
3
4
5
6
7
8
ENGL SH I 9
0 0 : 0 0
10
ANT 1
11
CABLE
12
13
ADD
14
0
15
16
17
18
(continued on next page)
Note:
To tune the TV to a channel not programmed
in the channel memory, you must use the
Channel Number buttons on the remote
control.
MENU
yzx •
Channel yz
TV front panel
MENU TV/VIDEO VOLUME CHANNEL
x •zy
MENU
Channel zy
POWER